Herunterladen
Teilen
Diese Seite drucken
Dell PowerVault 110T LTO-2-L Kurzanleitung
  1. Anleitungen
  2. Marken
  3. Dell Anleitungen
  4. PC-Komponenten
  5. PowerVault 110T LTO-2-L
  6. Kurzanleitung
Dell PowerVault 110T LTO-2-L Kurzanleitung

Dell PowerVault 110T LTO-2-L Kurzanleitung

Vorschau ausblenden

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 4

Quicklinks

Diese Anleitung herunterladen
PowerVault
TM
110T LTO-2-L
Quick Start Guide
Information in this document is subject to change without notice. © 2005 Dell Inc. All rights reserved. Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden. Trademarks used in this text: PowerVault, Dell and the DELL logo are trademarks of Dell Inc.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.
April 2005 P/N 7050 Rev A00
Regulatory and Safety Information
See the safety and regulatory notices in
your Product Information Guide.
The external PowerVault 110T LTO-2-L drives are compact external units that connect to the host computer
through an external SCSI port. Installing the external drive involves four steps: configuring the drive, attaching
the SCSI cable(s), checking SCSI termination, and attaching the power cord.
Set the SCSI ID.
Your tape drive is shipped with a default SCSI ID of 6, but it can be assigned any unused ID between 0 and 15.
Do not use SCSI ID 7 or SCSI ID 0. Dell does not recommend installing the drive onto a Narrow SCSI bus, as this
will restrict performance. The SCSI ID is set using the SCSI ID selector switch on the back panel of the drive.
Connect the SCSI interface cable.
The external LTO-2-L tape drive has two 68-pin, shielded SCSI interface connectors (ANSI Alternative 2) on the
rear panel. These connectors consist of two rows of ribbon contacts spaced 2.16 mm (0.085 in) apart. Either
connector can be used as a SCSI IN or SCSI OUT connection. This means you can use either connector to attach
the drive to a host system or to another SCSI device.
Check the SCSI termination.
If the external LTO-2-L tape drive is the last device or the only device in a SCSI chain, you must install a
termination plug on the unused SCSI connector.
Termination power is disabled as a default for external drives.
Connect the power cable.
Connect a power cable to the AC power connector on
the back of the external tape drive.
Installation and Configuration
See the Dell PowerVault 110T LTO-2-L Ultrium Tape
Drive Installation Guide for detailed information on
the installation and configuration of your system.
SCSI Terminators
External Tape Drive
External SCSI device
SCSI Controller
(termination enabled)
Example 1: SCSI termination
in a system that has only
external SCSI devices.
External SCSI device
External Tape Drive
SCSI Controller
(termination disabled)
Internal SCSI device
(termination enabled)
Example 2: SCSI termination
in a system that has both
internal and external SCSI devices.

Werbung

loading

Verwandte Anleitungen für Dell PowerVault 110T LTO-2-L

Inhaltszusammenfassung für Dell PowerVault 110T LTO-2-L

  • Seite 1 Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.
  • Seite 2                                   PowerVault                ...

  • Seite 3: Guide De Démarrage Rapide

    Guide de démarrage inutilisé entre 0 et 15 peut être attribué. N'utilisez le numéro d'identification SCSI 7 ou 0. Dell ne recommande pas l'installation du lecteur dans un bus SCSI étroit, ceci risque de réduire les performances. Le numéro d'identification rapide SCSI est configuré...
  • Seite 4 Ihr Bandlaufwerk wird standardmäßig mit einer SCSI-ID von 6 versandt. Es kann ihm jedoch eine beliebige ID zwischen 0 und 15 zugewiesen werden. Verwenden Sie nicht SCSI-ID 7 oder SCSI-ID 0. Dell rät davon ab, das Laufwerk auf einem Narrow-SCSI-Bus zu installieren, da dies zu Leistungseinschränkungen führen würde.
  • Seite 5 EgÐatÜstash Ðai RýÒmish PaÓamÝtÓwn Ελεγκτής SCSI (τερματισμός AnatÓÝctÑ ston Odhgü EgÐatÜstashj thj MonÜdaj Magnhtotainßaj απενεργοποιημένος) Dell PowerVault 110T LTO-2-L Ultrium gia lÑÕtomÑÓÞ ÕlhÓoÔüÓhsh sxÑtiÐÜ mÑ thn ÑgÐatÜstash Ðai th ÓýÒmish twn ÕaÓamÝtÓwn tou sustÞmatüj saj. Ελεγκτής SCSI (τερματισμός Εσωτερική συσκευή SCSI ενεργοποιημένος)
  • Seite 6 ‫מדריך להתחלה מהירה‬ ‫ צר, מאחר‬ISCS ‫ אינה ממליצה להתקין את הכונן על אפיק‬Dell .0 ‫ עם זיהוי‬SCSI ‫ עם זיהוי 7 או‬SCSI -‫תשתמש ב‬ .‫ הנמצא בלוח האחורי של הכונן‬SDSI ‫ מוגדר בעזרת מתג בורר הזיהוי‬SCSI ‫שהוא יגביל את הביצועים. זיהוי‬...
  • Seite 7 110T LTO-2-L SCSI ID の設定 の設定 このテープドライブの SCSI ID は、デフォルトの 6 ですが、0～ 15 の未使用の ID を割り当てる クイックスタート ことができます。SCSI ID に 7 または 0 を使用しないでください。Dell は、ナロー SCSI バス上へ のドライブのインストールをお勧めしません。（ナロー SCSI バス上にドライブをインストールすると、 ガイド ドライブの性能が落ちます。）SCSI ID は、ドライブの背面パネルにある SCSI ID セレクタを使用し オン / オフ...
  • Seite 8                                   PowerVault               ...

  • Seite 9: Guia De Início Rápido

    Guia de início rápido entre 0 e 15. Não use a ID de SCSI 7 ou a ID de SCSI 0. A Dell não recomenda instalar a unidade em um barramento SCSI estreito, uma vez que ele restringirá o desempenho. A ID de SCSI é configurada usando o interruptor do seletor da ID de SCSI localizado no painel traseiro da unidade.
  • Seite 10 Información de seguridad y reglamentaria Selector de identificaciones SCSI Conectores SCSI Consulte los avisos reglamentarios y de seguridad en la Guía de información del producto. � � � �� � �� � � � � �� � �� �� � � �� � � � �� � � ���� � � � �� � � �� �� �� � � �� � �� � � � � �� � �� �� � � �� � � � � � �� � �� � � �� � �� � � � � �� � �� ��� � � �� � �� � � �� PowerVault �...