Guarantee / Environment; Specifications Techniques - Skil 9370 Hinweise

Mounting of accessories 6
G
! disconnect the plug
- clean spindle C and all parts to be mounted
- tighten clamping flange E with spanner F while
pushing spindle-lock button G
- for removing accessories handle vice-versa
! grinding/cutting discs become very hot during
use; do not touch them until they have cooled
down
! always mount backing pad when using sanding
accessories
! never use a grinding/cutting disc without the label
("blotter") which is glued onto it
Before using the tool
G
- ensure that accessory is correctly mounted and firmly
tightened
- check if accessory runs freely by turning it by hand
- test-run tool for at least 30 seconds at highest no-load
speed in a safe position
- stop immediately in case of considerable vibration or
other defects and check tool to determine the cause
On/off locking switch H 7
G
- switch on tool 7a
! be aware of the sudden impact when the tool is
switched on
! before the accessory reaches the workpiece, the
tool should run at full speed
- lock switch 7b
- unlock switch/switch off tool 7c
! before switching off the tool, you should lift it
from the workpiece
! the accessory continues to rotate for a short time
after the tool has been switched off
Speed selection wheel L 6 (9380/9385)
G
- for determining the right speed table 0 can be used
as reference
! always test out first on a piece of scrap material
Electronic soft-start (9380/9385)
G
Ensures reaching the maximum speed smoothly without
a sudden impact when tool is switched on
Electronic constant speed (9380/9385)
G
Keeps the speed at a constant level as the load
increases
Electronic overload protection (9380/9385)
G
Stops the motor automatically in case the tool is
overloaded for a longer period of time
For restarting the motor:
- switch off tool
- let tool cool down for 30 seconds
- switch on tool
Grinding 8
G
- move the tool back and forth with moderate pressure
! never use a cutting disc for side grinding
Cutting 9
G
- do not tilt the tool while cutting
- always move the tool in same direction as arrow on
tool head, in order to prevent the tool from being
pushed out of the cut in an uncontrolled manner
- do not apply pressure on the tool; let the speed of the
cutting disc do the work
- the working speed of the cutting disc depends on the
material to be cut
- do not brake cutting discs with side pressure
Holding and guiding the tool
G
- always hold the tool firmly with both hands, so you
will have full control of the tool at all times
- provide for a secure stance
- pay attention to the direction of rotation; always hold
the tool so, that sparks and grinding/cutting dust fly
away from the body
- keep ventilation slots J 6 clear and uncovered
APPLICATION ADVICE
Instead of flange E 6 the "CLIC" quick-clamping flange
G
K 6 (SKIL accessory 2610388766) can be used;
grinding/cutting discs can then be mounted without the
use of accessory keys

GUARANTEE / ENVIRONMENT

Always keep tool and cord clean (especially the
G
ventilation slots)
! do not attempt to clean ventilation slots by
inserting pointed objects through openings
! disconnect the plug before cleaning
This SKIL product is guaranteed in accordance with
G
statutory/country-specific regulations; damage due to
normal wear and tear, overload or improper handling will
be excluded from the guarantee
In case of a complaint, send the tool undismantled
G
together with proof of purchase to your dealer or the
nearest SKIL service station (addresses as well as the
service diagram of the tool are listed on
www.skileurope.com)
Dispose of the tool by sorting tool, accessories and
G
packaging for environment-friendly recycling (the plastic
components are labeled for categorized recycling)
F
INTRODUCTION
Cet outil sert au meulage, au tronçonnage et à
G
l'ébarbage de pièces en métal et en pierre sans utiliser
de l'eau; combiné avec des accessoires spécifiques, cet
outil peut également servir au brossage et au ponçage

SPECIFICATIONS TECHNIQUES 1

6