Specifications; Specific Safety Rules - Makita DA3000R Betriebsanleitung

ENGLISH
1 Tighten
2 Chuck key
3 Switch lever (Paddle switch)
4 Speed control screw

SPECIFICATIONS

Model
Capacities
Steel .................................................................. 10 mm
Wood ................................................................. 15 mm
-1
No load speed (min ) ....................................... 0 – 1,400
Overall length ..................................................... 272 mm
Net weight .............................................................. 1.6 kg
• Due to the continuing program of research and devel-
opment, the specifications herein are subject to change
without prior notice.
• Note: Specifications may differ from country to country.
Power supply
The machine should be connected only to a power sup-
ply of the same voltage as indicated on the nameplate,
and can only be operated on single-phase AC supply.
They are double-insulated in accordance with European
Standard and can, therefore, also be used from sockets
without earth wire.
Safety hints
For your own safety, please refer to enclosed Safety
instructions.

SPECIFIC SAFETY RULES

DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to drill safety rules. If you use this power tool
unsafely or incorrectly, you can suffer serious per-
sonal injury.
1. Hold power tools by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a "live" wire will make exposed
metal parts of the tool "live" and shock the oper-
ator.
2. Always be sure you have a firm footing.
Be sure no one is below when using the tool in
high locations.
3. Hold the tool firmly.
4. Keep hands away from rotating parts.
5. Do not leave the tool running. Operate the tool
only when hand-held.
6. Do not touch the drill bit or the workpiece imme-
diately after operation; they may be extremely
hot and could burn your skin.
7. Some material contains chemicals which may be
toxic. Take caution to prevent dust inhalation
and skin contact. Follow material supplier safety
data.
SAVE THESE INSTRUCTIONS.
Explanation of general view
5 Lock-off lever
6 Clockwise
7 Counterclockwise
8 Reversing switch knob
DA3000R/DA3000V
GEB002-2
9
10 Brush holder cap
11 Screwdriver
WARNING:
MISUSE or failure to follow the safety rules stated in
this instruction manual may cause serious personal
injury.
OPERATING INSTRUCTIONS
Installing or removing drill bit (Fig. 1)
Important:
Always be sure that the machine is switched off and
unplugged before installing or removing the bit.
To install the bit, place it in the chuck as far as it will go.
Tighten the chuck by hand. Place the chuck key in each
of the three holes and tighten clockwise. Be sure to
tighten all three chuck holes evenly.
To remove the bit, turn the chuck key counterclockwise in
just one hole, then loosen the chuck by hand.
After using the chuck key, be sure to return it to the origi-
nal position.
Switch action
CAUTION:
Before plugging in the machine, always check to see that
the paddle switch actuates properly and returns to the
"OFF" position when released.
For machines with lock-off lever (Fig. 2)
To prevent the switch lever from being accidentally
squeezed, a lock-off lever is provided. To start the
machine, slide the lock-off lever in the direction of the
arrow and squeeze the switch lever. Machine speed is
increased by increasing pressure on the switch
lever.Release the switch lever to stop. A speed control
screw is provided so that maximum machine speed can
be limited (variable).
For machines without lock-off lever (Fig. 3)
To start the machine, simply squeeze the switch lever.
Machine speed is increased by increasing pressure on
the lever. Release the lever to stop. A speed control lever
is provided so that maximum machine speed can be lim-
ited (variable).
Reversing switch action (For DA3000R only)
(Fig. 4)
CAUTION:
• The switch lever (paddle switch) cannot be squeezed
with the reversing switch knob positioned halfway
b
between marking and
squeezed forcibly, the machine may be damaged.
• Always check the direction of rotation before drilling.
• You cannot obtain reversing switch action with the
switch lever squeezed since the reversing switch knob
is thereby locked.
This machine has a reversing switch to change the direc-
tion of rotation. Turn the reversing switch knob so that its
b
protrusion will point to
c
or marking for counterclockwise rotation.
Limit mark
c
marking. If it is
marking for clockwise rotation
3