Cleaning And Maintenance; Cleaning Your Vacuum Cleaner - ROWENTA X-TREM POWER CYCLONIC RO62 Serie Bedienungsanleitung

RO_ASPIRATEUR_XTREM POWER_RO62_764270-01_764270/01 16/04/14 13:56 Page10
EN

CLEANING AND MAINTENANCE

IMPORTANT: Always turn off and disconnect your
vacuum cleaner
maintenance procedures.
1 - Empty the dust box
IMPORTANT Empty the dust box after each use.
• Withdraw the tube from the vacuum opening (Fig.2)
• Open the lid of your vacuum cleaner (fig.15).
• Remove the dust box (12) from its compartment by using the
handle (Fig.16).
• Lean on the opening button (OPEN) of the dust box lid and
then lift the lid (Fig.17) to withdraw it completely (Fig.18).
• Empty the dust box over a dustbin (Fig.19)
• Place the lid back on the box by putting the corresponding
parts on the appropriate notches (Fig.20), then pull it down
until you hear a 'CLICK' (Fig.21).
• Place the box back in its casing (Fig.22).
2 - Clean the dust box and the
filtration system
The air we breathe contains particles that can be allergenic:
larva and dust mite faeces, mould, pollen, smoke and animal
waste (hair, skin, saliva, urine). The finest particles can
penetrate deep inside the respiratory system or cause
inflammation, affecting the entire respiratory function.
(H)EPA ([High] Efficiency Air Particle Filter) filters retain even
the smallest particles.
Thanks to the (H)EPA filter, the air released into the room is
cleaner than the air vacuumed.
IMPORTANT In order to improve the performance
of your vacuum cleaner, remember to clean the
dust box and the filtration system every 3 months.
• Withdraw the tube from the vacuum opening (Fig.2)
• Open the lid of your vacuum cleaner (fig.15).
• Remove the dust box (12) from its compartment by using the
handle (Fig.16).
a. Clean the dust box
• Press the opening button (OPEN) of the dust box lid and then
lift the lid (Fig.17) to withdraw it completely (Fig.18)
• Then withdraw the casing that contains the separator from
the lid by pressing on the OPEN button (Fig.23-24).
• Detach the separator from its casing (Fig.25).
• Rinse the separator (13 a), its casing (13b) and the dust box
lid (12b) under clean water. You may use some mild soap
(Fig.26).
• Dry them with a cloth (Fig 27).
• Once they are dry, place the separator back in its casing by
using the notch designed for that purpose (Fig.28), then
* According to model : These parts are specific to certain
models or they are accessories that can be purchased se-
parately.
before performing any
replace the whole assembly (13 a + 13b) inside the dust box
lid by using the appropriate notch (Fig.29) until you hear a
'CLICK' (Fig.30)
b. Clean the filtration system
• Press on the opening clips of the HEPA filter case (Fig.31)
• Withdraw the filter case HEPA (16) from the dust box (12c)
(Fig 32)
• Separate the foam filter (16b) from the HEPA filter (16a)
(Fig.33)
• Tap the HEPA filter over a dustbin (Fig.34)
• Wash the foam filter (16b) and the HEPA filter (16a) under
clear running water and allow to dry 12 H (Fig.35).
ATTENTIONTo clean the HEPA filter, wash it under
normal running water. In order to not damage it,
avoid scraping it with an accessory.
• Wash the dust box (12c) under running water (Fig.36) and
dry it with a soft cloth.
• Once it is dry, reposition the foam filter (16b) on the HEPA
filter (16a) (Fig.37)
• Replace the filter case (16a + 16b) on the dust box (12c) by
using the notches designed for that purpose (Fig.38) until
you hear a 'CLICK'. (Fig.39)
• Place the lid back on the box by putting the corresponding
parts on the appropriate notches (Fig.20), then pull it down
until you hear a 'CLICK' (Fig.21).
• Place the box back in its casing (Fig.22).
IMPORTANT Replace the filtration system once a
year.
3 – Replace the filtration system
The HEPA filter* case ref. ZR902301* is available at your local
retail store or at one of our Authorised Service Centres.
• Withdraw the tube from the vacuum opening (Fig.2)
• Open the lid of your vacuum cleaner (fig.15).
• Remove the dust box (12) from its compartment by using the
handle (Fig.16).
• Press on the opening clips of the HEPA filter case (Fig.40)
• Withdraw the HEPA filter case (16) from the dust box (12c)
(Fig.41).
• Throw the filter case (16a + 16b) in a dustbin (Fig.42) and
replace it with a new filter case (Fig.43-44).
• Place the box back in its casing (Fig.22).
• Close the lid of your vacuum cleaner.
4 • Cleaning your vacuum cleaner
Wipe the body of the appliance and the accessories with a soft
cloth (Fig.45). Do not use any detergents, or corrosive or
abrasive products.
10