Residual Risks; Technical Data; Unpacking; Attachment - Parkside PHDB 4 C3 Originalbetriebsanleitung

6.12 Residual risks

m CAUTION
Even if used correctly, it is not possible to exclude non-appar-
ent residual risks entirely.
• Injuries due to slipping on waste water.
• Injuries or property damage due to the high-pressure water
jet.

7. Technical data

Engine
Type
Displacement cm³
Nominal output kW (PS)
at 3500 min
-1
Nominal speed min
Fuel tank l
Fuel
Fuel consumption l/h
at full load
Oil volume - engine l
Oil type – engine
Spark plug
Water connection
Hose diameter mm
Supply temperature °C
max.
Supply pressure MPa (bar) 0.2 - 0.5 (2 - 5)
max.
Pump
Working pressure MPa (bar)
Max. working MPa (bar)
pressure
Flow rate l/min
Max. flow rate l/min
Opening temperature °C
thermal valve
Inlet connection
Outlet connection
Dimensions and weight
Length x width x mm
height
Typical operating kg
weight
Cleaning agents Only use cleaning agents
approved for high-pressure
cleaners.
Noise emission
Noise measurement value determined in accordance with EN
60335-2- 79. The A-rated noise level is typically as follows:
Sound pressure level L .......................... 90 dB(A)
pA
Uncertainty K ...............................................3 dB
pA
Sound power level L ........................... 105 dB(A)
WA
Uncertainty K ..............................................3 dB
WA
DVO175
173
3.3 (4.5)
-1 3500+/-100
1.2
Petrol, unleaded
0.8 - 0.9
0.4
SAE10W30
F7RTC
min. 12.7
40
17.9 (179)
19.9 (199)
8.7
9.1
55 - 60
G 3/4 (EU)
M22x1,5
620x500x1040
22
Wear ear protection to prevent hearing damage!
Vibration values (vector total of three directions) determined in
accordance with EN 60335-2-79:
Hand spray gun handle
Vibration value ......................................1,62 m/s
Centre hand spray gun
Vibration value ..................................... 2,27 m/s²
Uncertainty K ........................................ 0,85 m/s²
NOTE:
The vibration level specified in these instructions has been
measured in accordance with the standardised measuring pro-
cedure specified in EN 60335-2-79 and can be used to make
equipment comparisons. The specified vibration emission value
can also be used to make an initial exposure estimate.
m WARNING
• The vibration level varies in accordance with use and may
be higher than the value specified in these instructions in
some cases. There is a risk of underestimation of the vibra-
tion load if the appliance is used regularly in this manner.
To estimate the vibration load during a specific working
period accurately, periods during which the appliance is
switched off (or running, but not being used) must also be
taken into account. This can significantly reduce the vibra-
tion load over the total working period.

8. Unpacking

• Open the packaging and remove the device carefully.
• Remove the packaging material as well as the packaging
and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for transport dam-
age.
• If possible, store the packaging until the warranty period
has expired.
m DANGER
The device and packaging materials are not toys! Children
must not be allowed to play with plastic bags, film and small
parts! There is a risk of swallowing and suffocation!
m WARNING
• Exercise caution when unpacking, transporting and stor-
ing due to the high weight of the machine. These activities
should be carried out by two people.
• Make sure that the appliance is standing on a level and
flat surface while unpacking, and during assembly, stor-
age as well as during operation, inspection, maintenance
and when at a standstill.

9. Attachment

9.1 Fitting the handle (Fig. 3)
Insert the bow-type handle (1) on the base frame of the device.
Press the two push buttons on the base frame and push the
bow-type handle (1) completely until it clicks into place.
2
GB/IE/NI 9