SSS Siedle SET CVSG 850-1 Produktinformation Seite 10

English
Application
The Smart Gateway starter kit for
surface mounting contains all the
components you need to accept a
door call with video on your smart-
phone and open the door.
Upgrade capability
The starter kit can be extended with
the following components. The
overall extension must not exceed
10 users, whereby one door station
supports two users.
• Video indoor station Siedle Basic
• Audio indoor station Siedle Basic
• Door station of the In-Home bus
system
Further system components may be
needed.
Performance features
BCV 850-1-...
• Integrated camera with automatic
day/night switchover, LED lighting
and 2-stage heating
• Integrated door loudspeaker
• Adjustable voice volume
• Number of integrated call but-
tons: 1
• Acoustic button acknowledgement
can be activated
• Backlit nameplates exchangeable
from the front
• for surface mounting with brushed
stainless steel panel
Performance features SG 150-...
• Support for the Siedle app for
iPhone or Android smartphone
• Up to 10 IP users (subject to
licence, 5 licences included)
• Group call of up to 6 IP users
• Parallel call to IP users and
In-Home bus end devices possible
• Direct door dialling from list
• Central video memory with auto-
matic time controlled deletion of
images (data protection compliant)
Performance features Siedle App
• Door calls using the app
• Mobile network connection
• Worldwide accessibility
• Secure and intuitive app operation
10
Performance features
SNG 850-...:
• 10 bus addresses for supplying the
bus users
• Integrated door release and light
contact
• Programming: manual or via
BPS 650-... (Windows PC) with
ZBVG 650-... and PRI 602-... USB
Electrical voltage
• Mounting, installation and ser-
vicing work on electrical devices may
only be performed by a suitably
qualified electrician. Failure to
observe this regulation could result
in the risk of serious damage to
health or fatal injury due to electric
shocks.
• Operation at an altitude of up to
2000 m above sea level.
• Observe EN 62368-1! In a building
installation, an all-pole mains switch
with a contact opening of at least
3 mm must be provided. The device
must not be exposed to water drops
or sprayed water! Sufficient ventila-
tion must be ensured. Pay particular
attention to ensure that ventilation
slots are not covered.
• When using stranded cores as
cable material, these must be fitted
with wire end ferrules without fail.
Electrostatic charging
As a result of electrostatic charging,
direct contact with the circuit board
can result in destruction of the
device. Direct contact with the circuit
board must therefore be avoided.
In the case of video systems, the fol-
lowing mounting situation must be
avoided at all costs:
• direct backlight
• direct sunlight
• very bright image backgrounds
• highly reflective walls opposite the
camera
• lamps or direct light sources
Scope of supply SET CVSG 850-1
• BCV 850-1-... E
• SG 150-...
• ANG 600-...
• SNG 850-...
• Siedle screwdriver
• This product information
Door station mounting
1 Unscrew the front of the housing.
To do this, release the Siedle screw
on the underneath of the housing.
Hinge the front of the housing
forward.
2 Surface mounting the door sta-
tion. Recommended mounting
height appr. 1.50 m /4.9 ft. to centre
device. Please note: The cable is
inserted in the lower area of the
base plate!
3 Strip back the installation cable
close to the wall (appr. 10 mm)
and insert the cores into the base
plate. Fasten the base plate using 4
screws. Close the two openings at
the top using rubber stoppers. Install
in accordance with the terminal
diagram.
The cores may only be laid in the
admissible installation space.
4 The pick-up angle of the camera
can be mechanically preadjusted on
the vertical and horizontal by appr.
30° depending on the mounting
situation. To change the pick-up
direction of the camera, it can be
positioned in the required direction.
To change the pick-up direction,
loosen the two cross-head screws
slightly. Position the camera in the
required direction. Then fix the