Herunterladen Inhalt Inhalt Diese Seite drucken
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 31
Polarity Inversion Duration menu -
display : dUr
(only the Selwatch model
T
3-03, 3-04
ype
By default, the device displays 4. The polarity
of the electrodes is inverted every four hours.
In the event of problems with the electrodes,
you may change the duration of the cycle
(askyour technician for advice).
Amperage menu - display : INT
(only the Selwatch model 3
T
3-03, 3-04
ype
By default, the device is set to 10 amperes and
displays 10. You may change the amperage if
there are problems with the electrodes (ask
your
technician for advice about this).
The display shows a value of between 1 and 10.
Reset menu - display : rCL
(only for the analysis values)
Press
C
twice to return the whole Chlorine
Cl
menu to its default settings.
ACL menu
This menu is for technical support only, so do
not change anything in it. Press
seconds to exit the menu.
At the end of the countdown,
the device displays NOR.
You may:
Launch a top-up chlorination (over-production
of chlorine) Press
display shows CLC. Chlorination will be
accelerated for five hours until a maximum
chlorine content of 4 ppm is obtained.
Place the regulation function on standby
(by-pass)
+
Press
for 10 seconds
The display shows Byp. Press
seconds to put the electrolyser or chlorine meter
pump back in regulated mode.
+
Press
to stop the countdown.
This will trigger a chlorine and pH analysis
request (without changing anything). Switch
the machine off and then on again to restart
the countdown, if you so wish.
21
3-05)
and
3-05)
and
C
for five seconds. The
Cl
+
+
again for 10
Common functions
Programming the Chlorine and pH menu..
Adjust the chlorine and pH settings
The dial always shows the true chlorine content
and pH of your swimming pool.
Press and hold down
requested setting value on the dial. Then increase
or decrease the value using the
The device is set to 1.5 ppm for the chlorine
and 7.4 for the pH by default.
Launch an immediate and forced analysis
Press
if the device has undertaken three or four
analyses).
Control the reagents level
Press
the display:
IIIIII: there are more than 1.000 analyses left.
999 to 099: indicates the number of remaining
analyses.
999 to 099 (flashing): warning that there is no
more reagent.
Press
for three
Cl
Note: the device can still make several more
Press
to reset the counter to zero. When the display
flashes, press
Display the most recent contents measured
Press
value is available, the display indicates ---.
Press... to enter
the pH menu
Press... to navigate
the menu
Press... to enter
a setting and change it
Press ... for three
seconds to validate
and exit the pH menu
C
Cl
C
or
C
for three seconds (valid only
Cl
pH
C
or
C
for five seconds then read
Cl
pH
C
or
C
for 3 seconds to leave the menu.
Cl
pH
analyses once the counter reaches zero.
C
C
or
then the
Cl
pH
C
C
or
twice.
Cl
pH
C
C
or
for eight seconds. If no content
pH
Cl

pH menu

C
pH
C
pH
C
pH
C
pH
C
or
to see th
pH
+
and
buttons .
+
and
buttons
+
then
+
then press
to
switch from one
setting to another
+
then
or
to
change the value

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

SelwatchSelwatch phSelwatch platinum

Inhaltsverzeichnis