mundoclima MUCSR H9 Serie Benutzer- Und Installationshandbuch Seite 74

Operation of buttons
1
ON/OFF
SHORT
CUT
2
TIMER
MODE
ON
TEMP
3
TIMER
FAN
OFF
4
SLEEP
LED
TURBO
5
1
ON/OFF Button
This button turns the air conditioner ON
and OFF.
2 MODE Button
Press this button to modify the air conditioner
mode in a sequence of following:
AUTO COOL DRY
3
FAN Button
Used to select the fan speed in four steps:
AUTO LOW MED
NOTE: You can not switch the fan speed in
AUTO or DRY mode.
4
SLEEP Button
Active/Disable sleep function. It can
maintain the most comfortable temperature
and save energy. This function is available
on COOL, HEAT or AUTO mode only .
, ,
For the detail, see sleep operation in
,
,,
, ,
USER S MANUAL.
NOTE: While the unit is running under SLEEP
mode, it would be cancelled if MODE, FAN
SPEED or ON/OFF button is pressed.
5 TURBO Button
Active/Disable Turbo function. Turbo function
enables the unit to reach the preset temper-
ature at cooling or heating operation in the
shortest time(if the indoor unit does not
support this function, there is no
corresponding operation happened when
pressing this button.)
6
7
6
7
8
9
10
11
12
8
9
HEAT
FAN
10
HIGH
,,
11
12
74
UP Button( )
Push this button to increase the indoor
o
temperature setting in 1 C increments to 30 C.
DOWN Button( )
Push this button to decrease the indoor
o
temperature setting in 1 C increments to 17 C.
NOTE Temperature contol is not available
in Fan mode.
SHORTCUT Button
Used to restore the current settings or
resume previous settings.
On the first time connecting to the power,
if push the SHORTCUT button, the unit
will operate on AUTO mode, 26 C, and fan
speed is Auto.
Push this button when remote controller is
on, the system will automatically revert
back to the previous settings including
operating mode, setting temperature, fan
speed level and sleep feature(if activated).
If pushing more than 2 seconds, the system
will automatically restore the current
operation settings including operating mode,
setting temperature, fan speed level and
sleep feature(if activated ).
TIMER ON Button
Press this button to initiate the auto-on
time sequence. Each press will increase
the auto-timed setting in 30 minutes
increments. When the setting time displays
10.0, each press will increase the auto-
timed setting 60 minutes increments.
To cancel the auto-timed program, simply
adjust the auto-on time to 0.0.
TIMER OFF Button
Press this button to initiate the auto-off time
sequence. Each press will increase the auto
-timed setting in 30 minutes increments.
When the setting time displays 10.0, each
press will increase the auto-timed setting
60 minutes increments. To cancel the auto-
timed program, simply adjust the auto-off
time to 0.0
Swing Button
Used to stop or start vertical louver movement
and set the desired left/right air flow direction.
The vertical louver changes 6 degree in angle
for each press. And the temperature display
, ,
area of indoor unit displays
second. If keep pushing more than 2 seconds,
the vertical louver swing feature is activated.
, And the display area of indoor unit displays
,
, flashes four times, then the tempera-
IIII
ture setting reverts back. If the vertical louver
swing feature is stopped, it displays LC and
remains on for 3 seconds.
NOTE: For some units , the indoor units
, ,
display when the swing feature is
, ,
activated, and display when the
swing feature is stopped.
Swing Button
Used to stop or start horizontal louver move-
ment or set the desired up/down air flow
direction. The louver changes 6 degree in
angle for each press. If keep pushing more
than 2 seconds, the louver will swing up and
down automatically.
LED Button
Disable/Active indoor screen Display. When
pushing the button, the indoor screen display
is cleared, press it again to light the display.
o
o
O
for one
, ,