Technical Data; Safety Instructions; Specified Conditions Of Use - Berner BACHDD-1 BL 18 V Originalbetriebsanleitung

TECHNICAL DATA

CORDLESS IMPACT DRILL DRIVER
Code ...................................................................................................
Drilling capacity in steel ......................................................................
Drilling capacity in wood .....................................................................
Drilling capacity in brick and tile .........................................................
Wood screws (without pre-drilling) .....................................................
No-load speed 1st gear ......................................................................
No-load speed 2nd gear .....................................................................
Impact rate 1st gear............................................................................
Impact rate 2nd gear ..........................................................................
Torque with battery max.* (5.0 Ah) .....................................................
Battery voltage....................................................................................
Drill chuck range .................................................................................
Weight according EPTA-Procedure 01/2014 (1.5 Ah / 2.0 Ah) ...........
Weight according EPTA-Procedure 01/2014 (3.0 Ah / 4.0 Ah) ...........
Weight according EPTA-Procedure 01/2014 (9.0 Ah) ........................
Noise/vibration information
Measured values determined according to EN 60745.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (K = 3 dB(A)) ..................................................
Sound power level (K = 3 dB(A)) ......................................................
Always wear ear protectors!
Total vibration values (vector sum in the three axes) determined
according to EN 60745.
Vibration emission value a
h
Percussion drilling into concrete......................................................
Uncertainty K= .................................................................................
Drilling into metal .............................................................................
Uncertainty K= .................................................................................
Screwing..........................................................................................
Uncertainty K= .................................................................................
* Measured according to factory standard N 877318.
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745
and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for diff erent applications, with
diff erent accessories or poorly maintained, the vibration emission may diff er. This may signifi cantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running
but not actually doing the job. This may signifi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the eff ects of vibration such as: maintain the tool and the accessories, keep
the hands warm, organisation of work patterns.
WARNING! Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric
shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.

SAFETY INSTRUCTIONS

Wear ear protectors when impact drilling. Exposure to noise
can cause hearing loss.
Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory may
contact hidden wiring. Cutting accessory contacting a "live" wire
may make exposed metal parts of the power tool "live" and could
give the operator an electric shock.
Hold power tool by insulated gripping surfaces, when
performing an operation where the fastener may contact
hidden wiring. Fasteners contacting a "live" wire may make
exposed metal parts of the power tool "live" and could give the
operator an electric shock.
Use auxiliary handle(s), if supplied with the tool. Loss of control
can cause personal injury.
Sawdust and splinters must not be removed while the machine is
running.
When working in walls ceiling, or fl oor, take care to avoid electric
cables and gas or waterpipes.
Remove the battery pack before starting any work on the machine.
ENGLISH
445 624 - Berner-BACHDD-1_BL_18V.indd 22 445 624 - Berner-BACHDD-1_BL_18V.indd 22
BACHDD-1 BL 18 V
....... BACHDD-1 BL 18 V 03 00001- 99999
................................ 13 mm
................................ 45 mm
................................ 13 mm
................................ 10 mm
........................... 0-550 min -11
......................... 0-2000 min
-1
......................... 0-8800 min -1
....................... 0-32000 min
-1
.............................. 135 Nm
................................ 18 V
.......................... 1,5-13 mm
............................... 2,2 kg
............................... 2,5 kg
............................... 2,9 kg
............................. 99,9 dB (A)
............................110,9 dB (A)
............................. 13,2 m/s
2
............................... 1,5 m/s
2
............................. 1,29 m/s 2
............................... 1,5 m/s
2
............................. 1,33 m/s 2
............................... 1,5 m/s
2
Do not dispose of used battery packs in the household refuse or by
burning them. Your power tool distributor will normally retrieve old
batteries to protect our environment.
Do not store the battery pack together with metal objects (short
circuit risk).
Use only System Berner chargers for charging System Berner
battery packs. Do not use battery packs from other systems.
Battery acid may leak from damaged batteries under extreme load
or extreme temperatures. In case of contact with battery acid wash
it off immediately with soap and water. In case of eye contact rinse
thoroughly for at least 10 minutes and immediately seek medical
attention.
Lithium Ion batteries submit only discharged at the collection
points. Pole isolated to avoid short circuits.
Warning! To reduce the risk of fi re, personal injury, and product
damage due to a short circuit, never immerse your tool, battery
pack or charger in fl uid or al-low a fl uid to fl ow inside them.
Corrosive or conductive fl uids, such as seawater, certain industrial
chemicals, and bleach or bleach containing products, etc., Can
cause a short circuit.

SPECIFIED CONDITIONS OF USE

The electronic cordless impact drill driver may be used for drilling,
percussion drilling, as well as screwdriving for independent use
away from mains supply.
Do not use this product in any other way as stated for normal use.
22
08.02.2019 08:52:59 08.02.2019 08:52:59