Intended Use; Safety Information - Scheppach HMS1080 Original Bedienungsanleitung

• Blade adjustment block
• Chip extraction
• Chip extraction extension
• Parallel fence
• Planing blade cover
• Swivel arm for planing blade cover
• Star grip screw with washer M6
• Crank handle
• Rubber feet 4x

4. Intended use

The surfacing and thicknessing plane is designed for
the surfacing and thicknessing of all types of whole
pieces of square, rectangular or chamfered convert-
ed timber.
The machine is to be used only for its pre-
scribed purpose.
m WARNING!
The following work must not be carried out:
• Insert work (in other words any work which does
not extend over the full length of the workpiece)
• Recesses, tenons or cut-outs
• Planing highly warped timber in which there is inad-
equate contact with the feed bench.
m The protective equipment on the appliance is
strictly prohibited to be disassembled, changed, used
in conflict with the designation and it is prohibited to
attach any protective equipment of other manufactur-
ers.
The bridge guard must not be removed during ma-
chining. The unused part of the blade shaft must be
covered.
Requirements for operating staff
The appliance may only be operated and maintained
by persons familiarised with it and informed about
possible risks.
Never let children work with the appliance. Never let
adults work with the appliance unless they have been
properly trained.
The operating staff must carefully read the Operating
Instructions before using the appliance.
Qualification: Apart from the detailed instructions by
a professional, no special qualification is necessary
for appliance using.
Minimum age: Persons over 18 years of age can
only work on the appliance. An exception includes
youngsters trained in order to reach knowledge un-
der supervision of the trainer during occupational ed-
ucation.
Local regulations may stipulate the minimum age of
the user.
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
Training: Using the appliance only requires corre-
sponding training by a professional or the Operating
Instructions. No special training is necessary.
The equipment is to be used only for its prescribed
purpose. Any other use is deemed to be a case of
misuse. The user / operator and not the manufacturer
will be liable for any damage or injuries of any kind
caused as a result of this.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial ap-
plications. Our warranty will be voided if the machine
is used in commercial, trade or industrial businesses
or for equivalent purposes.

5. Safety information

General Safety Instructions
WARNING! When using electric tools basic safety
precautions should always be followed to reduce
the risk of fire, electric shock and personal injury
including the following.
Read all these instructions before attempting to op-
erate this product and save these instructions.
Safe operation
1 Keep work area clear
- Cluttered areas and benches invite injuries.
2 Consider work area environment
- Do not expose tools to rain.
- Do not use tools in damp or wet locations.
- Keep work area weil lit.
- Do not use tools in the presence of flamma-
ble liquids or gases.
3 Guard against electric shock
- Avoid body contact with earthed or ground-
ed surfaces (e.g. pipes, radiators, ranges,
refrigerators).
4 Keep other persons away
- Do not let persons, especially children, not
involved in the work touch the tool or the ex-
tension cord and keep them away from the
work area.
5 Store idle tools
- When not in use, tools should be stored in
a dry locked-up place, out of reach of chil-
dren.
6 Do not force the tool
- lt will do the job better and safer at the rate
for which it was intended.
7 Use the right tool
- Do not force small tools to do the job of a
heavy duty tool.
- Do not use tools for purposes not intended;
or example do not use circular saws to cut
tree limbs or logs.
GB | 23