Functional Description - Makita DVC862L Betriebsanleitung

FUNCTIONAL
DESCRIPTION
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before adjusting or checking function on the tool.
Installing or removing battery
cartridge
CAUTION:
Always switch off the tool before
installing or removing of the battery cartridge.
CAUTION:
Hold the tool and the battery car-
tridge firmly hen installing or removing battery
cartridge. Failure to hold the tool and the battery
cartridge firmly may cause them to slip off your hands
an d result in d amage to t h e tool an d batter y c artri d ge
and a personal injury.
Be careful not to pinch your fin-
CAUTION:
gers when opening or closing the battery cover.
Failure to do so may cause personal injury.
To install the battery cartridge, release the lock first,
and open the battery cover. And then, insert the battery
c artri d ge.
Fig.1: 1. Lock 2. Battery cover
Align the tongue on the battery cartridge with the groove
in t h e h ousing an d slip it into pla c e. I nsert it all t h e w a y
until it lo c ks in pla c e w it h a little c li c k. T h en lo c k t h e
batter y c o v er.
Fig.2: 1. Battery cartridge
T o remo v e t h e batter y c artri d ge, sli d e it f rom t h e tool
w h ile sli d ing t h e button on t h e f ront o f t h e c artri d ge.
CAUTION:
Always install the battery cartridge
fully until the red indicator cannot be seen. I f not,
it may accidentally fall out of the tool, causing injury to
y ou or someone aroun d y ou.
CAUTION:
Do not install the battery cartridge
forcibly. I f t h e c artri d ge d oes not sli d e in easil y , it is
not being inserte d c orre c tl y .
NOTE: T h e c leaner d oes not w ork w it h onl y one
batter y c artri d ge.
Indicating the remaining battery
capacity
Only for battery cartridges with the indicator
Fig.3: 1. I n d i c ator lamps 2. C h e c k button
P ress t h e c h e c k button on t h e batter y c artri d ge to in d i-
c ate t h e remaining batter y c apa c it y . T h e in d i c ator lamps
lig h t up f or a f e w se c on d s.
Indicator lamps
Lighted
NOTE: D epen d ing on t h e c on d itions o f use an d t h e
ambient temperature, t h e in d i c ation ma y d i f f er slig h tl y
f rom t h e a c tual c apa c it y .
Indicating the remaining battery capacity
Fig.4: 1. Battery indicator 2. C h e c k button
Fig.5
P ress t h e c h e c k button to in d i c ate t h e remaining batter y
c apa c ities. T h e batter y in d i c ators c orrespon d to ea c h batter y .
Battery indicator status
On
Tool / battery protection system
The tool is equipped with a tool/battery protection sys-
tem. T h is s y stem automati c all y c uts o f f po w er to t h e
motor to e x ten d tool an d batter y li f e. T h e tool w ill auto-
mati c all y stop d uring operation i f t h e tool or batter y is
placed under one of the following conditions:
Overload protection
W h en t h e tool is operate d in a manner t h at c auses it to
d ra w an abnormall y h ig h c urrent, t h e tool automati c all y
stops w it h out an y in d i c ation. I n t h is situation, turn t h e
tool o f f an d stop t h e appli c ation t h at c ause d t h e tool to
be c ome o v erloa d e d . T h en turn t h e tool on to restart.
9 ENGLISH
Off Blinking
mal f un c tione d .
Off
Blinking
Remaining
capacity
to
to
to
to
C h arge th e
battery .
T h e battery
may h av e
Remaining
battery
capacity
to
to
to
C h arge th e
battery