Cleaning And Maintenance; Technical Data - AEG SR 4370 Bedienungsanleitung

English
52
52
The instructions for setting alarm time 1 are given below:
1. Switch the device to standby with the STANDBY button.
2. Press the ALARM 1 button. " " appears on the display
and the hours for the switch-on time fl ash.
3. Set the hours with the UP / DOWN buttons.
4. Confi rm your setting with the ALARM 1 Button. The
minute digits start fl ashing.
5. Set the minutes with the UP / DOWN buttons.
6. Save the alarm time with the ALARM 1 button.
The activated alarm will be displayed in standby mode with
the symbol " " for the fi rst alarm and the symbol " " for
the second alarm.
NOTE:
For technical reasons, the activated function cannot be
displayed during the operation of the display.
Turn off the Alarm Signal
Press the button STANDBY to stop the alarm signal.
Snooze
The automatically set alarm function can be switched off for
9 minutes with the SNOOZE button.
NOTE:
If the snooze function is activated, the notifi cation
"SNOOZE" will appear in the display.
Deactivate Alarm Function
1. Switch the device to standby.
2. Press the ALARM 1 button or the ALARM 2 button. The
symbol for the fi rst or the second alarm will disappear.

Cleaning and Maintenance

CAUTION:
Do not immerse the device in water.
• Always remove the mains plug before cleaning the
machine.
• Any marks on the surface can be wiped off with a slightly
damp cloth without any additives.
Troubleshooting
Problem Cause
The unit The unit is
cannot be blocked and
operated "hangs"
SR4370CD-DAB-USB_IM
Problem
No DAB Radio
reception
Problems with
DAB radio
reception
No sound
Poor sound
quality
Alarm function
does not
sound
CD can not be
played back.
CD jumps
during play-
back.

Technical Data

Model: ....................................................SR 4370 CD / DAB+ / USB
Power supply: ............................................................. 230 V ~, 50 Hz
Battery operation: ..................................6 x 1,5 V, Type UM 2 /R 14
Power consumption:................................................................. 15 W
Protection class: ..............................................................................Ⅱ
Net weight: .............................................................. approx. 1.57 kg
Radio section
Solution
Disconnect the power
The right to make technical and design modifi cations in
supply for 5 seconds.
the course of continuous product development remains
Then switch the
reserved.
device on again.
This device has been tested according to all relevant current
Reset the device to
CE guidelines, such as electromagnetic compatibility and low
the factory defaults.
voltage directives, and has been constructed in accordance
see "Settings menu"
with the latest safety regulations.
Cause
Telescopic an-
tenna incorrectly
aligned
No Digital Radio
can be received
in your area
Depending on
the location, you
may not be able
to receive some
stations at all or
with interference
in your region.
see also note on
page 49
Volume is too
low
Radio signal too
weak
Volume set too
low
CD is not insert-
ed or inserted
incorrectly.
Batteries too
weak.
Check the disc
for fi ngerprints,
dirt or scratches.
Frequency ranges: ..................................FM 87.5 ~ 108.0 MHz
........... DAB/DAB+ 174.92 ~ 239.20 MHz
Solution
Fully extend the
telescopic antenna
and align it vertically.
Switch to FM mode to
receive these stations.
If these stations are
transmitted via VHF.
Find out more on the
internet site of the
radio station.
Increase the volume
Try to adjust the
antenna position.
Increase the volume
with the control (7).
Ensure that the disc is
inserted with the label
facing upwards.
Insert new batteries
or operate the device
with the mains lead.
Check the disc for
fi ngerprints, dirt or
scratches.
27.05.16