Specifications; Da: Installations Vejledning - Interlogix ATS1160 Installationsanleitung

Tamper
The reader is provided with a tamper facility. When connected
to the bus, tamper data is transmitted to the Advisor Master
with system data.
Reader menus
Enter via the Installer menu and select the menu "Remote
Devices", then select "RAS".
The following options are available:
1. Tamper option: Enable/disable (default enabled)
2. Reader Address: Changing reader address (1 to 16),
default = 16
3. RTE (egress): Enable/disable the request to exit and open
collector (default disabled)
4. Backlight option: Permanent/Access only (default Access
only)
5. Buzzer option: enable/disable reader buzzer (default
enabled)
6. Restore factory defaults
Reader wiring
Table 1: Reader wiring
Red +12V Positive 10 to 30 V
Black 0 Volts DC supply ground
White D+ RS-485 Data +
RS-485 Data −
Green D−
Yellow RTE Request to exit button
Violet OC Open Collector output used to control a door
relay
Spare wires are not used.
Use WCAT54 cable. Cable length depends on the bus
configuration.
Reader LEDs
Table 2: Reader LEDs
LED pos. Colour
Left Green
Red
Green / red flashing
Green flashing
Middle Orange
Right Red flashing

Specifications

Number of card combinations
Supply voltage
Supported card types
Connectivity
Cable
2 / 16
supply, 80 mA
Description
System disarmed
ATS125x: System armed
Valid card presented
Door open time
ATS4000: System not ready
ATS125x: Always on
Alarm
15
72x10
10 to 30 V
ACT4xxE, Mifare Classic
(7 Byte UID), Mifare DESfire
EV1, Mifare Plus, Mifare
Ultralight
ATS data bus
LIYY 2 m
Normal operating current
Maximum operating current
Open collector output (OUT terminal) 14 V
LED
Carrier frequency
Material of design housing
Dimensions of housing (H x W x D)
Field strength
Pry-off tamper
Operating temperature
Storage temperature
Relative humidity
Regulatory information
Manufacturer
UTC Fire & Security Americas Corporation, Inc.
1275 Red Fox Rd., Arden Hills, MN 55112-6943, USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, Netherlands
Version
This document applies to ATS1160N and ATS1161N
hardware version 2.0 or later.
Certification
Protection IP67
class
1999/5/EC (R&TTE directive): Hereby, UTC Fire &
Security declares that this device is in compliance with
the essential requirements and other relevant
provisions of Directive 1999/5/EC.
2002/96/EC (WEEE directive): Products marked with
this symbol cannot be disposed of as unsorted
municipal waste in the European Union. For proper
recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or
dispose of it at designated collection points. For more
information see: www.recyclethis.info.
Contact information
www.utcfireandsecurity.com or www.interlogix.com
For customer support, see www.utcfssecurityproducts.eu

DA: Installations vejledning

Beskrivelse
ATS1160/ATS1161 Læsere er en Mifare kort læser
(kompatibel med ACT4xxE kort). Læseren er designet for
montering inde som ude, f.eks. på dør karme eller på
lokaliteter som kræver en smal læser.
ATS1161 er med tastatur for Kort+Pin applikationer.
ATS1160/ATS1161 indeholder alle nødvendige komponenter
for tilslutning til ATS centralens system bus samt den lokale
databus på ATS125x. Læseren har indgang for UD-tryk og en
OC udgang til styring af et dør-relæ.
Læseren kan konfigureres gennem den indbygget menu
struktur, som er tilgængelig via en RAS der er tilsluttet system
bus. Eller ATS1482 konfigurations kort.
P/N 1070070 (ML) • REV C • ISS 17APR13
50 mA at 13.8 V
80 mA at 13.8 V
max. at 50 mA max.
Tri-color
13.56 MHz
Plastic
140 x 44 x 20 mm
According to EN 300 330
Optical sensor
−40 to +55°C
−40 to +55°C
<95%, noncondencing