DeWalt DWE46172 Bersetzt Von Den Originalanweisungen Seite 18

EngLIsh
Dust Extraction (Fig. F–H)

WARNING: Use only power tools recommended by
D WALT with this attachment. For technical specifications
e
refer to technical Data.
For more information about D
e
with this attachment, please contact one of the authorised
services centres listed on the back cover or refer to the full
details of our after-sales service available on the Internet at:
www.2helpU.com.

WARNING: This attachment must be used with a dust
extractor system class M suitable for mineral dust.
ALWAYS wear certified safety face or dust mask.
nOtE: Ensure hose connection is secure.
nOtE: The amount of dust retained by the dust extractor
vacuum is dependent on its filter system. Refer to the dust
extractor vacuum instruction manual for more information.
All D WALT dust collection shrouds are designed to connect
e
and secure easily with the D WALT universal DWV9000
e
connector. The DWV9000 connector comes pre-installed on
some D WALT dust extractors. Consult your local dealer for
e
compatible extractors.
Connecting the DWV9000 onto the Shroud
(Fig. F)
nOtE: If the DWV9000 is not installed on your dust
extractor hose, refer to Installing the DWV9000 on a Dust
Extraction hose.
1. With the DWV9000 connector
shroud's dust port 4 .
2. Lock the DWV9000 connector
Installing the DWV9000 on a Dust Extraction
Hose (Fig. G–H)
The DWV9000 can be attached to a 32 mm dust
extraction hose.
For 32 mm hoses:
1. Remove the existing hose connector
clockwise, or if connector is permanently attached, remove
by cutting.
2. Install the universal DWV9000 connector
by turning anticlockwise.
OPERATION

WARNING: To reduce the risk of injury, ALWAYS turn
off tool and disconnect the tool from the power
source before making any adjustments or removing
or installing attachments or accessories. This applies
to both the grinder and the dust extractor. Such
preventative safety measures reduce the risk of starting the
tool accidentally.

WARNING: For your own safety, read the instruction
manual for both the grinding tool and the dust extractor
before using any accessory. Failure to heed these warnings
may result in personal injury and serious damage to the
tool and the accessory. When servicing this tool, use only
identical replacement parts.
16
WALT power tools compatible
unlocked, slide it onto the
9
9 to secure.
10 by twisting
9 onto the hose
nOtE: The amount of dust retained by the dust extractor
vacuum is dependent on its filter system. Refer to the dust
extractor instruction manual for more information.
1. Ensure all assembly instructions have been completed.
2. Turn the dust extractor vacuum on as instructed in the dust
extractor vacuum instruction manual.
3. Turn the tool on as instructed in the tool instruction manual
and allow it to reach full speed before making contact with
work surface.
4. Place the surface grinding shroud to flat work surface such
as a floor or wall and begin grinding.
5. When surface grinding is complete, turn the tool off and
disconnect from the power source. Allow the tool to stop
rotating before laying it down.
nOtE: The surface grinding shroud and dust extractor vacuum
will only be effective when used with a diamond surface cup
wheel on a flat surface.
MAINTENANCE
Your D WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.

WARNING: To reduce the risk of injury, ALWAYS turn
off tool and disconnect the tool from the power
source before making any adjustments or removing
or installing attachments or accessories. This applies
to both the grinder and the dust extractor vacuum.
Such preventative safety measures reduce the risk of
starting the tool accidentally.
Lubrication
Your power tool requires no additional lubrication.
Cleaning

WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.

WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
Optional Accessories

WARNING: Since accessories, other than those offered
by D WALT, have not been tested with this product, use
e
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
WALT recommended
e