Bravo BST 300 Bedienungsanleitung Seite 5

TECHNICAL FEATURES:
• Voltage 11-13 Vdc
• Maximum current 13 A
• Maximum pressure 300 mbar (4,4 psi)
800 mbar (11,7 psi)
• Maximum flow 450 l/min
• FIRST USE (FOR BST 800 BATTERY ONLY)
To avoid accidental starts during transport, the battery is
disconnected. Before use, open the battery box by unscrewing
the 4 screws "A" (Figure 1). Connect the red cable to the positive
terminal of the battery and the black cable to the negative
terminal. Put the box back.
IMPORTANT CHARGING NOTES
1. Longest life and best performance can be obtained if the battery is charged when the air tem-
perature is between 18°- 24°C (65°F and 75°F). DO NOT charge the battery in an air temperature
below +40°F(+4.5°C), or above +105°F (+40.5°C). This is important and will prevent serious
damage to the battery.
2. The charger and battery may become warm to touch while charging. This is a normal condition,
and does not indicate a problem.
3. DO NOT immerse charger in water or any other liquid.
WARNING: DO NOT ALLOW ANY LIQUID TO GET INSIDE THE CHARGER.
ELECTRIC SHOCK MAY RESULT
4. DO NOT attempt to charge the battery with any chargers other than the ones supplied with this
manual. The charger and battery are specifically designed to work together. BST BATTERY CAN BE
CHARGED DIRECLTY BY MEANS OF THE CAR CIGARETTE PLUG.
5. The charger is not intended for any use other than charging the battery in the Inflator. Any other
uses may result in risk of fire, electric shock or electrocution.
6. Make sure cord is located so that it will not be stepped on, tripped over, or otherwise subjected to
damage or stress.
7. Do not operate charger with a damaged cord or plug.
8. Do not operate the charger if it has received a sharp blow, been dropped, or otherwise damaged
in any way.
9. Do not disassemble charger. Incorrect reassembly may result in a risk of electric shock, electro-
cution or fire.
10. Never use another products charger to charge this product. Always use identical replacement
parts only.
BST 300
BST 800 and BST 800 BATTERY
1. Connect the inflator to the power supply (excluding the BST 800 BATTERY) with the cables
provided. The BST 300 is provided with a plug for car cigarette lighter; additional socket with
crocodile clips for direct connection to a 12 Vdc battery is provided as well.
The BST 800 is provided with crocodile clips to be connected to a 12 Vdc battery.
WARNING! Ensure correct polarity
(RED TERMINAL TO POSITIVE OUTPUT OF THE BATTERY)
2. Connect the hose to the output port (outgoing arrow) by means of the fitting provided.
3. Connect the hose to the inflation valve on the inflatable via the included fittings. It is important to
choose the suitable connection to the valve and to verify that no air leakage is present. Make sure
there are no bottlenecks in the air path (i.e. torn tube, incorrect connections, etc.)
4. Adjust the pressure regulator wheel to the pressure value recommended by the manufacturer.
5. The inflator will automatically stop when the pressure reaches the set value.
CAUTION! DO NOT RUN THE INFLATOR MORE THAN 15 MINUTES. COOL DOWN THE UNIT
FOR 20 MINUTES AFTER . THE INFLATOR CON BE STOPPED BY PRESSING "OFF" PB.
CAUTION! PLEASE CONSIDER THE PROPER MAX INFLATION PRESSURE OF THE
INFLATABLE. ALWAYS SET THE MAX RECCOMMENDED PRESSURE BY MEANS OF
THE PRESSURE REGULATOR WHEEL. DO NOT OVER-INFLATE.
1. Connect the hose to the inlet port (see arrow) by means of the proper fittings.
CAUTION! MAKE SURE THAT, DURING DEFLATION, THE UNIT WILL NOT OPERATE
UNATTENDED. SWITCH OFF THE UNIT WHEN NO AIR CAN BE EXTRACTED FROM
THE INFLATABLE.
CAUTION! THE INFLATOR CAN BE DAMAGED BY SAND, POWDER OR WATER ENTERING
INTO THE INLET PORT. THIS WILL CAUSE THE OVERHEATING AND WILL DAMAGE THE
TURBINE. SWITCH OFF IMMEDIATELY THE INFLATOR IF THE PISTON MODULE IS
NOT ACTIVATED.
CLEANING THE INFLATOR
TO INFLATE:
TO DEFLATE: