Bosch Universal GrassCut 18 Originalbetriebsanleitung Seite 29

Note: The rapid-charging procedure is only possible when
the battery temperature is within the allowable charging
temperature range, see section "Technical Data".
(Slow) Flashing of the Green Battery Charge Indicator
When the charging condition of the battery is
80%, the green battery charge indicator
flashes slowly.
The battery can be removed for immediate use.
Continuous Lighting of the Green Battery Charge
Indicator
Continuous lighting of the green battery
Full
charge indicator indicates that the battery is
fully charged.
When the battery is not inserted, continuous lighting of the
battery charge indicator indicates that the mains plug is in-
serted in the socket outlet and that the battery charger is
ready for operation.
Continuous Lighting of the Red Battery Charge Indicator
Continuous lighting of the red battery charge
indicator indicates that the temperature of the
battery is not within the allowable charging temperature
range, see section "Technical Data". As soon as the allowable
charging temperature range is reached, the battery charger
automatically switches to rapid charging.
Flashing Red Battery Charge Indicator
A flashing red battery charge indicator indic-
ates a different malfunction of the charging
procedure, see section "Troubleshooting – Causes and Cor-
rective Measures".
Operation
Caution: Switch the garden tool off and remove the
u
battery before performing any maintenance.
The cutting line continues to rotate for a few seconds
u
after the trimmer is switched off. Allow the motor/cut-
ting line to stop rotating before switching on again.
Do not briefly switch off and on again several times in
u
a row.
Only use Bosch approved cutting elements. Cutting
u
performance will vary with different cutting elements.
Switching On and Off (see figure H)
To switch on, firstly press the lock-off button (9). Then
press the On/Off switch (8) and keep it pressed.
Troubleshooting
d.c.
Lawn trimmer/Edge cutter
Bosch Power Tools
To switch off, release the On/Off switch (8).
Lawn Trimming/Edge Cutting (see figures I − K)
Lawn trimming (see figure I)
Press the foot pedal (4) and set the 48° angle for lawn trim-
ming.
Move the trimmer left and right, keeping it well away from
the body. Cut higher grass in steps.
Edge cutting (see figure J)
Press the foot pedal (4) and set the 36° angle for edge cut-
ting. Rotate the handle by 180° and then turn the trimmer
clockwise to the desired working position.
Guide the trimmer along the edge of the lawn. By using the
wheel, you avoid contact with solid surfaces or walls to pre-
vent rapid wear of the cutting line.
Cutting around trees and bushes (see figure K)
Press the foot pedal (4) and set the 24° angle for cutting
around trees and bushes.
Carefully cut around trees and bushes so that they do not
come into contact with the cutting line. Plants can die if you
damage the bark.
Dismounting the spool, winding up the cutting
line and mounting the spool (see figures N to L)
Remove the battery before replacing the spool.
u
Press both latches of the spool cover together and remove
the spool cover (13). Afterwards, remove the empty spool
(14).
Cut off approx. 6 m line from the refill roll. Thread the end of
the line into the spool's hole for line wind-up (15). Thread/
work the line under the hook (17). Then, thread/work the
line up and through the slot (18) in the spool. Afterwards,
wind up the thread on the spool uniformly and tightly.
Slide the other end of the cutting line through the hole for
line guiding (19) in the trimmer head and mount the spool
back into the trimmer head. Affix the spool by mounting the
spool cover (13).
The spool cover (13) can only be mounted in one position.
Line Feeding
IntelliFEED
The trimmer is equipped with the IntelliFEED system, which
automatically rolls off the line to retain the cutting diameter.
English | 29
F 016 L94 011 | (17.09.2019)