Safety Instructions; Additional Safety Warnings - Facom E.516ST-30 Übersetzung Der Originalanweisung

SAFETY INSTRUCTIONS

When using an electrical wrench, basic precautions should always
be followed, including the following:
READ ALL INSTRUCTIONS
BEFORE USING
THIS WRENCH.

WARNING: Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions listed below may result in electric shock, fire
and/or serious injury.

WARNING: Do not attempt to modify or repair
the wrench.

WARNING: Do not charge the battery at ambient
temperatures below 4 °C (39 °F) or above 40 °C
(104 °F). Follow all charging instructions and do not
charge the wrench outside of the temperature range
specified in the instructions. Charging improperly or at
temperatures outside of the specified range may damage
the battery and increase risk of fire.

WARNING: To reduce the risk of fire, electrical shock
or injury:
• Shock Hazard. To protect against risk of electrical shock, do
not put charging base in water or other liquid.
• Do not allow to be used as a toy. Close attention is
necessary when used by or near children.
• Use only as described in this manual. Use only
manufacturer's recommended attachments.
• Do not use with damaged cord or plug. If wrench is
not working as it should, has been dropped, damaged, left
outdoors, or dropped into water, return it to a service center.
• Do not pull or carry by cord, use cord as a handle, close a
door on cord, or pull cord around sharp edges or corners.
Keep cord away from heated surfaces.
• Do not unplug by pulling on cord. To unplug, grasp the
plug, not the cord.
• Do not handle charger, including charger plug, and
charger terminals with wet hands.
• Do not put any object into openings. Do not use with any
opening blocked; keep free of dust, lint, hair, and anything that
may reduce air flow.
• Do not charge the unit outdoors.
• Use only the charger supplied by the manufacturer
to recharge.
• Do not incinerate the wrench even if it is severely
damaged. The batteries can explode in a fire.
• Do not allow the cord to hang over the edge of a table or
counter or touch hot surfaces. The unit should be placed or
mounted away from sinks and hot surfaces.
• Plug the charger directly into an electrical outlet.
• Use the charger only in a standard electrical outlet
(220-240V/50Hz).
• Unplug the charger from outlet before any routine
cleaning or maintenance.
• Leaks from battery cells can occur under extreme
conditions. If the liquid, which is a 20-35% solution of
potassium hydroxide, gets on the skin (1) wash quickly with
soap and water or (2) neutralize with a mild acid such as
lemon juice or vinegar. If the liquid gets into the eyes, flush
them immediately with clean water for a minimum of 10
minutes. Seek medical attention.

Additional Safety Warnings

a ) This wrench is intended for professional, commercial
or industrial use only.
b ) Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used with
another battery pack.
c ) Do not use a battery or wrench that is damaged or
modified. Damaged or modified batteries may exhibit
unpredictable behavior resulting in fire, explosion or risk
of injury.
d ) Do not expose a battery or wrench to fire or
excessive temperature. Exposure to fire or temperature
above 130 °C (266 °F) may cause explosion.
e ) Have servicing performed by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the product is maintained.
f ) Only for use with J611-DOCK chargers.
SAVE THESE
INSTRUCTIONS
Additional Safety Rules for Torque Wrenches

WARNING:
• ALWAYS use safety glasses. Everyday eyeglasses are NOT safety
glasses. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:
• ANSI Z87.1 eye protection (CAN/CSA Z94.3)
• Do not use the unit outdoors. Unit intended for indoor use only.
• ALWAYS ensure accessories are not chipped or damaged to
reduce the risk of loose debris causing injury
• Do not expose to excessive heat or humidity to avoid
deformation or corrosion, which may affect accuracy.
• Do not use this wrench in water since fluid ingress will affect the
circuitry resulting in damage and potentially electrical shock.
• NEVER use on live electrical circuit, wrench does not protect
you from electrical shock. Turn off power before use
• Over torque (exceeding stated maximum capacity by 130%
can result in damage, breakage or affect accuracy)
• Avoid use of solvents, chemicals, liquids
• Do not attempt to disassemble or repair. Refer to an authorised
service centre.
• Guard against snagging of clothing, hair, jewellery or anything
that could impair movement of the product or work piece and
lead to damage or injury.
EngLIsH
19