Seav LRX 2217/M Bedienungsanleitung Seite 6

rent direction, the control unit reverses gear.
O F M
THER UNCTIONING ODALITIES
Venetian Functioning:
If, by pressing the Up or Down key of a memorised radio-control for at
least 2 sec. during this phase, an operator present type functioning is
obtained: in this way, it is possible to carry out slight rotary movements,
in one direction or the other of the Venetian reeds, to modulate the filter-
ing of the light to ones' liking. If the radio-control key is pressed for more
than 2 sec., the blind moves up or down, depending on the which key has
been pressed, until the motor time expires, equal to 3 minutes; if, during
ascent or descent, a Stop control is given, the control unit stops the fas-
tening. In case during ascent or descent a control is given of the same
current moving direction, the control unit continues the movement.
In case during ascent or descent a control is given of the opposite cur-
rent direction, the control unit reverses gear.
Operator present functioning:
In this modality, it is necessary to constantly keep the control for the fas-
tening movement in the direction relating to the pressed key, active. The
movement stops when the control is released.
Functioning with Infinite motor time:
By pressing the radio-control in this modality, the control unit is started
for an infinite time, unless a further control is given, deactivating it.
G M C
ROUP OR AIN ENTRALISATION
IT IS also possible to insert equal radio-control codes (keys) to all control
units or by group, at a distance not higher than 20 metres from the con-
trol point, in order to obtain the main or partial movement of more
automations.
R - / W
ADIO CONTROL AND OR IRELESS
KEY
The programming of the transmission codes of the radio-control and/or
Wireless sensors can be carried out as follows:
Programming with 1 or 2 Keys radio-control:
press the "SEL" key (for example, with the point of a pen), located at the
extremity of the box, three sounds will be heard at the same time, con-
S
ENSORS PROGRAMMING THROUGH
firming programming entry, press the key of the radio-control to be asso-
ciated to the ascent movement continuously for 5 seconds until the con-
trol unit emits a confirming sound, subsequently, press the second key of
the radio-control to be associated to the descent movement continuous-
ly for 5 seconds until the control unit emits two confirming sounds and,
after one second, the control unit will emit four confirming sounds, sig-
nalling programming end.
If, after programming of the first code the second code is not given, the
control unit exits programming emitting four confirming sounds and
selecting functioning with only one code.
Programming with radio-control (BeFree Series) 3 Keys:
press the "SEL" key (for example, with the point of a pen), located at the
extremity of the box, three sounds will be heard at the same time, con-
firming programming entry, press the BeFree Series radio-control Up key
to be associated to the ascent movement continuously for 5 seconds
until the control unit emits a confirming sound, subsequently, after one
second, the control unit will emit four confirming sounds signalling pro-
gramming end.
Programming with Wireless sensors:
press the "SEL" key (for example, with the point of a pen), located at the
extremity of the box, three sounds will be heard at the same time, con-
firming programming entry, press the dedicated key inside the Wireless
Sensor until the control unit emits a confirming sound, subsequently, after
one second, the control unit will emit four confirming sounds signalling
programming end.
No communication.
In case of no communication between the Wireless Sensor and the con-
trol unit, the safety ascent of the fastening will automatically start after 20
minutes. In case no communication persists, further controls will always
"SEL" bring the control unit in safe conditions.
F R -CONTROLS
URTHER ADIO
It is possible to repeat the above described programming operations to
insert further Radio-controls, up to a maximum of 6 different ones and up
to a maximum of 3 different Wireless sensors, inside the control unit
memory.
In case the memory already contains 6 memorised Radio-controls and/or
- 6 -
/ W S P
AND OR IRELESS ENSORS ROGRAMMING