Inhaltsverzeichnis
Werbung
Quicklinks
CVDC2-S25 and CVPC2-S25T
VDS (Pressurized Vehicle Detection Camera System)
CVDC2-S25............... Tubular Dust Proof Camera System, 120Vac input, adjustable sunshield, internal surge suppression, 128x wide dynamic range, 25x
zoom, co-ax, RS485
CVPC2-S25T..............Tubular Pressurized Camera System, 115Vac input, adjustable sunshield, internal surge suppression, 128x wide dynamic range, 25x
zoom, co-ax, RS485
© 2013, Moog Inc. All Rights Reserved
Moog Inc.
Sensor and Surveillance Systems
3650 Woodhead Drive Northbrook, IL. USA 60062
+1.847.498.0700 Fax: +1.847.498.1258 www.moogS3.com
Installation and Operation Instructions
Before attempting to connect or operate this product, please
read these instructions completely.
81-IN5498 051614
Werbung
Inhaltsverzeichnis
Verwandte Anleitungen für Moog CVDC2-S25
Inhaltszusammenfassung für Moog CVDC2-S25
- Seite 1 CVDC2-S25 and CVPC2-S25T VDS (Pressurized Vehicle Detection Camera System) CVDC2-S25....Tubular Dust Proof Camera System, 120Vac input, adjustable sunshield, internal surge suppression, 128x wide dynamic range, 25x zoom, co-ax, RS485 CVPC2-S25T....Tubular Pressurized Camera System, 115Vac input, adjustable sunshield, internal surge suppression, 128x wide dynamic range, 25x zoom, co-ax, RS485 Moog Inc.
-
Seite 2: Important Safeguards
IMPORTANT SAFEGUARDS SAFETY PRECAUTIONS Read these instructions. Keep these instructions. CAUTION Heed all warnings RISK OF ELECTRIC SHOCK DO NOT OPEN Follow all instructions. Do not use this apparatus near water. CAUTION: TO REDUCE THE RISK OF Clean only with damp cloth. ELECTRIC SHOCK, DO NOT REMOVE COVER ( OR BACK). - Seite 5 V D S Value Features Optional Accessory Multi-Plane Adjustable SunShield position to protect against glare on lens Cable Feed Through hides and protects cables Pop Out Tabs Lanyard Cable allows for safely retains housing pole mounting during installation Installers Connection Board allows for easy hook-ups Hand Hold underlaid grip point...
-
Seite 6: Electrical Specifications
Electrical Specifications Contents of Box VDS UNITS Power 120Vac Class 2 Only 120Vac: 17 watts Heater (16 watts), Blower (1 watt) Tools Required: Phillips head screwdriver Midspan English Some Models 120Vac: 17 vatios Calentador (16 vatios), soplador (1 vatio) Herramientas requeridas: Destornillador principal Phillips Hardware Packet Español 120Vac: 17 watts... - Seite 7 CAUTION: When assembling the mounting bracket, make sure Proper Assembly of Mounting Bracket all the wiring access holes are facing towards the rear of the base mounts access portal. • PRECAUCIÓN: Al montar la consola de montaje, cerciórese de que todos los agujeros de acceso del cableado son revestimiento hacia la parte posterior del portal bajo del acceso de los montajes.
-
Seite 8: Wall Mounting
WALL MOUNTING If running wire through a conduit to the housing mount, rst install Attach mount to wall with suitable hardware (not provided). appropriate ttings to the mount base. • Si se ejecuta a través de un cable de conducto a la carcasa de montaje, primero instale los •... - Seite 9 Pole Mount Option (Use Steel Straps to Mount) Gasket Nipples Crimp Cable Ties Cable Cable Feed cable through bracket, pierce the gasket nipples Crimp the connectors as needed. Then use cable ties (as needed). Place the gasket as shown. on the nipples to secure device, leave extra cable. •...
- Seite 10 (B- Completely loosen) (A- Slightly loosen) In order to rotate the rear cover, slightly loosen the screw marked (A) and completely loosen the screw marked (B). Then make all of the nessecary wiring connections. • Conecte la tierra entrante con el poste de tierra según lo demostrado. •...
-
Seite 11: Wiring Diagram
Black - focus Red - common Green - zoom black - line white - neutral green - ground NOTE: (must be connected to ground for surge protection). Wiring Diagram CAUTION: Be sure to securely tighten all fittings to ensure a liquid tight seal. Failure to do so could allow water to enter the housing and damage the camera and lens. - Seite 12 Camera Sled Ring Screw Camera Sled Loosen the screws shown on the picture and turn the camera Install the camera using provided screws and rubber spacer, to sled ring to the desired angle and re-tighten. center lens (if needed). • Afloje los tornillos demostrados en el cuadro y dé...
- Seite 13 Pressurize the Unit Cont. Place the air chuck on the ll valve and begin lling until pressure relief valve opens. • Coloque la tirada del aire en la válvula del tanque y comience a llenar hasta que la válvula de descarga de presión se abra.
- Seite 14 After purging and re lling, check the housings pressure. It should be around 5-7psi (0.35-0.5bar). • Después de purgar y de rellenar, compruebe la presión de las cubiertas. Debe estar alrededor de 5-7psi (0.35-0.5bar). • Après la purge et le remplissage, vérifiez la pression Connectors de logements.