10. Transport
Transport of li-ion battery packs:
The shipping of li-ion battery pack is subject to laws
related to the carriage of hazardous goods (UN
3480 and UN 3481). Inform yourself of the currently
valid specifications when shipping li-ion battery
packs. If necessary, consult your freight forwarder.
Certified packaging is available from Metabo.
Only send the battery pack if the housing is intact
and no fluid is leaking. Remove the battery pack
from the machine for sending. Prevent the contacts
from short-circuiting (e.g. by protecting them with
adhesive tape).
Remove the battery pack from the machine to
transport the machine.
11. Troubleshooting
The electronic signal indicator (4) lights up and
the load speed decreases. The temperature is too
high! Run the machine in idling until the electronic
signal indicator switches off.
The electronic signal display (4) flashes and
the machine does not start. The restart protection
is active. The machine will not start if the battery
pack is inserted while the machine is on. Switch the
machine off and on again.
The electronic signal display (4) flashes and
the machine does not start. Press the button (5);
the LEDs indicate the charge level. When the
battery pack is empty it must be recharged.
Electronic safety stop: The electronic signal
display (4) flashes and the machine was
SWITCHED OFF automatically. If the slew rate of
the current is too high (for example, if the machine
suddenly seizes or kickback occurs), the machine
switches off. Switch off the machine. Switch it on
again and continue to work as normal. Try to
prevent the machine from seizing. See chapter 4.2.
12. Accessories
Use only original Metabo or CAS (Cordless Alliance
System) battery packs and accessories.
Use only accessories that fulfil the requirements
and specifications listed in these operating
instructions.
Fit accessories securely. If the machine is operated
in a holder: secure the machine well. Loss of control
can cause personal injury.
See page 4.
A Chargers
B Battery pack
C Grinding wheel(always use with safety guard
attached)
D Lamellar grinding disc (always use with safety
guard attached)
E Parting safety guard.
F Cut-off wheel (always use with parting safety
guard attached)
G Diamond discs (always use with parting safety
guard attached)
H Hand guard (for attaching under the additional
side-mounted handle.)
I Extension piece (for working with supporting
discs. Increases the distance between the
spindle and the supporting disc by approx.
35 mm)
J Supporting disc for fibre discs (always attach
using the supporting disc clamping nut
supplied.) (always use with the hand guard
attached.)
K Fibre discs (always use with the hand guard
attached.)
L Steel wire brushes (always use with the hand
guard attached.)
M Adjusting nut (9)
For a complete range of accessories, see
www.metabo.com or the catalogue.
13. Repairs
Repairs to power tools must only be carried
out by qualified electricians!
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. See
www.metabo.com for addresses.
You can download a list of spare parts from
www.metabo.com.
14. Environmental Protection
The sanding dust generated may contain
hazardous materials: do not dispose of with the
household waste, but at a special collection point
for hazardous waste.
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Battery packs must not be disposed of with regular
waste! Please return faulty or used battery packs to
your Metabo dealer!
Do not throw battery packs into water.
Only for EU countries: never dispose of
power tools in your household waste! Used
power tools must be collected separately and
handed in for environmentally compatible recycling
in accordance with European Directive 2012/19/EU
on waste electrical and electronic equipment and its
implementation in national legal systems.
Discharge the battery pack in the power tool before
disposal. Prevent the contacts from short-circuiting
(e.g. by protecting them with adhesive tape).
15. Technical Data
Explanatory notes on the specifications on page 2.
Changes due to technological progress reserved.
U
= Battery pack voltage
D
= max. diameter of accessory
max
t
= max. permitted thickness of clamping
max,1
shank on accessory when using clamping
ENGLISH en
17