Werbung
Verfügbare Sprachen
Verfügbare Sprachen
SETTING/DISPLAYING TIME ZONE
If you wish to display the time in another time zone (e.g. the time in Las Vegas, USA)
in spite of the DCF reception, you can set a time delay to the DCF time (+12h or -12h).
For this purpose, proceed as follows:
-
Press and hold the "S" button for about three seconds, until the symbol
"
" appears in the top right of the display. Release the button again.
-
Press and hold the "MODE" button for about 3 seconds, until the hours begin to
blink.
-
Set the hours with the "S" or "F" button. For a quick adjustment hold the corre-
sponding button for a longer period of time.
-
Briefl y press the "MODE" button to store the setting.
If you press and hold the "S" button for about three seconds, the display will
switch between the "normal" DCF time and the second time zone.
SETTING THE SECOND TIME ("DUAL TIME")
The radio alarm clock offers the option of displaying both the normal time and the
time of another time zone (e.g., the time in a far distant vacation spot).
-
First choose the display of the second time zone by briefl y pressing the "MODE"
button as many times as necessary until "DUAL TIME" is shown in the lower
right.
-
Press and hold the "MODE" button for about 3 seconds, until the hours of the
second time zone begin to blink.
-
Set the hours of the second time zone with the "S" or "F" button. For a quick
adjustment hold the corresponding button for a longer period of time.
-
Confi rm the setting by briefl y pressing the "MODE" button. The minutes of the
second time zone start fl ashing.
-
Set the minutes of the second time zone with the "S" or "F" button. For a quick
adjustment hold the corresponding button for a longer period of time.
-
Confi rm the setting by briefl y pressing the "MODE" button. This ends the setting
of the time for the second time zone.
The setting mode will automatically end (without saving the settings) if no
buttons are pressed for about 30 seconds.
ALARM FUNCTION
a) Displaying the alarm time
Briefl y press the "MODE" button as many times as needed until the time for Alarm 1
("AL1") or Alarm 2 ("AL2") is shown in the lower right of the display.
b) Setting the alarm
-
First, briefl y press the "MODE" button as many times as needed until the time for
Alarm 1 ("AL1") or Alarm 2 ("AL2") is shown in the lower right of the display.
-
Press and hold the "MODE" button for about 3 seconds, until the hours of the
alarm time begin to blink.
-
Set the hours of the alarm time with the "S" or "F" button. For a quick adjust-
ment hold the corresponding button for a longer period of time.
-
Confi rm the setting by briefl y pressing the "MODE" button. The minutes of the
alarm time start fl ashing.
-
Set the minutes of the alarm time with the "S" or "F" button. For a quick adjust-
ment hold the corresponding button for a longer period of time.
-
Confi rm the setting by briefl y pressing the "MODE" button. Setting of the alarm
time is complete.
The setting mode will automatically end (without saving the settings) if no
buttons are pressed for about 30 seconds.
c) Activating/deactivating the timed alarm
By briefl y pressing the "
" button on the front of the radio alarm clock multiple
times, you can activate/deactivate both of the alarm times. Corresponding symbols
appear in the lower right of the display:
Alarm 1 activated:
Alarm 2 activated:
Alarm 1 and Alarm 2 activated:
Alarm function turned off:
d) Stop alarm signal & sleep function ("SNOOZE")
At the set alarm time, an alarm signal will be emitted (also, the clock symbol blinks).
This can be ended by briefl y pressing the "
When the "SNOOZE/LIGHT" button is pressed on the top of the clock, the alarm
signal is interrupted for approx. 4 minutes (between the display of the hours and
minutes, "Zz AL" fl ashes) and is started again afterwards (snooze function).
If you do not pause or end the alarm signal, the automatic off function will do
so after about 4 minutes.
SELECTING THE TEMPERATURE UNIT °C/°F
Briefl y press the "°C/°F" button to choose the desired temperature unit for the
display of the indoor temperature.
This is possible only when the temperature is shown in the lower right of
the display. For more information, see the section "Switching Additional Dis-
plays".
Symbol "
"
Symbol "
"
Symbol "
" and "
"
No symbol on the display
" button.
CHOOSING LANGUAGE FOR WEEKDAY DISPLAY
To the right of the month display, the day of the week (abbreviated to two letters) is
shown. The language for this abbreviation can be adjusted.
For this purpose, proceed as follows:
-
Press and hold the "F" button (do not release).
-
After a few seconds, the display will show the language in the position of the
weekday (keep holding the "F" button!): "IT" = Italian, "FR" = French, "SP" =
Spanish, "EN" =English, "GE" = German.
-
When the desired language appears in the display (e.g., "EN" for English), release
the "F" button.
-
The device leaves the setting mode automatically.
ACTIVATING ILLUMINATION
Briefl y press the "SNOOZE/LIGHT" button on the top to activate the display illumina-
tion. To save power, the illumination switches off automatically after a few seconds.
SUMMER TIME DISPLAY
If the DCF signal contains information for Summer Time, "
right of the display.
LOCATION FOR INSTALLATION
Select an even, fl at and stable installation location. Protect valuable furniture sur-
faces by using an appropriate underlay; otherwise scratch marks may occur.
Set up the radio alarm clock in such a manner that it cannot fall over.
For perfect DCF reception, the radio alarm clock should not be installed near other
electronic devices, cables, metal parts, etc.
CLEANING AND MAINTENANCE
The product does not require any maintenance and should never be disassembled
for any reason.
Please use a soft, dry, clean cloth for cleaning. Do not apply too much pressure on
the display, as it may be damaged. It may become scratched.
Do not use any chemical cleaning agents, they can discolour the plastic housing.
DISPOSAL
a) Product
Electronic devices are recyclable waste and must not be disposed of in the
household waste!
Please dispose of the product, when it is no longer of use, according to the
current statutory requirements.
b) Batteries and rechargable batteries
As the end user, you are required by law (Battery Ordinance) to return all used bat-
teries/rechargeable batteries; disposal of them in the household waste is prohibited!
Contaminated batteries/rechargeable batteries are labelled with these sym-
bols to indicate that disposal in the domestic waste is forbidden. The sym-
bols for the relevant heavy metals are: Cd=Cadmium, Hg=Mercury, Pb=Lead
(the labelling is visible on the battery/rechargeable battery e.g. under the
refuse bin symbol shown on the left).
You can dispose of your used batteries/rechargeable batteries free of
charge at your community's collection point or any place where batteries/
rechargeable batteries are sold!
You thereby fulfi l your statutory obligations and contribute to the protection of the
environment.
DECLARATION OF CONFORMITY (DOC)
We, Conrad Electronic, Klaus-Conrad-Straße 1, D-92242 Hirschau, hereby declare
that this product conforms to the fundamental requirements and the other relevant
regulations of the directive 1999/5/EC.
You can fi nd the Declaration of Conformity for this product at
www.conrad.com.
TECHNICAL SPECIFICATIONS
Operating voltage:
3 V/DC (2 Batteries of type AA/Mignon)
Battery life:
approx. 1 year
Alarm Times:
2
Temperature display:
-9.9 Ð to + 49.9 Ð
Dimensions:
117 x 84 x 43 mm (W x H x D)
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1,
D-92240 Hirschau (www.conrad.com). All rights including translation reserved. Reproduction by
any method, e.g. photocopy, microfi lming, or the capture in electronic data processing systems
require the prior written approval by the editor. Reprinting, also in part, is prohibited. These ope-
rating instructions represent the technical status at the time of printing. Changes in technology
and equipment reserved.
© Copyright 2011 by Conrad Electronic SE.
" appears in the upper
Werbung
