MSR XGK EXPEDITION Handbuch Seite 4

FUEL INFORMATION
The XGK stove can burn a variety of fuels, using two interchangeable Jets.
1.
The GK Jet is used for white gas, unleaded auto gas, and aviation gas. This Jet is pre-installed in your stove.
2.
The X Jet is for kerosene, jet fuel, and diesel. This Jet is included in the parts kit with your stove.
MSR recommends that you use MSR® White Gas. It is the highest quality fuel available for your stove.
Other white gas brands include Coleman®, Crown®, and CampLite®. The fuels chart below is a guide to
help you find white gas when traveling internationally. Any fuel other than white gas may lead to rapid
stove clogging, requiring more frequent jet and fuel line cleanings. Do not use leaded fuels.
USA/UK Germany/
Japan
Canada Switzerland
White gas Kocherbenzin
White gas
Naphtha Reinbenzin
Petroleum
Kerosene Toh-yu
Kerosin
Unleaded
Autobenzin Gasoline
auto gas
Diesel Diesel
Diesel
LIMITED LIFETIME WARRANTY
This MSR stove has a limited lifetime warranty. Should this product fail during its life, return
it to MSR or an authorized MSR dealer. MSR will repair or replace it at our option, free of charge.
Repairs required due to improper use or care, negligence, product modification, or accident are not
covered under this warranty agreement but will be performed at a nominal charge upon request.
This warranty applies only to the original purchaser. Proof of purchase is required. Products
purchased from an independent dealer should be returned to the dealer for forwarding to MSR.
Shipping cost to MSR is the responsibility of the purchaser. Return postage will be paid by MSR.
MSR shall not be liable for any direct, indirect or incidental damages whatsoever that arise from
use of product.
Except as provided herein, MSR makes no warranties, express or implied including but not
limited to the implied warranties of merchantability and fitness for a particular purpose. MSR
shall not be liable for any consequential or incidental damages whatsoever.
This warranty gives you specific legal rights. You may also have other rights that vary from
state to state. Some states do not allow the exclusion or limitation of incidental or consequential
damages, or limitations or exclusions of implied warranties, so the above exclusion and limitation
may not apply to you.
CONTACT
For more product information or for safety-related information, contact MSR Customer Service.
MSR will also service your stove or provide replacement instructions on request.
Mountain Safety Research
4000 First Avenue South, Seattle, WA 98134 USA
Phone: 800.531.9531 or 206.505.9500
France Holland Spain
Pétrole à brûler Bencina
Wasbenzine
Essence C blanca
Petroleum
Kérosène Parafina
Lampolie
Essence sans Gasolina sin
Benzine
plomb plomo
Diesel Diesel Diesel
INSERTING PUMP INTO FUEL BOTTLE
1. IMPORTANT! O-rings and Pump Seal are extremely critical for safe operation of your stove.
Before using your stove, ensure that O-rings and Pump Seal are present, in good condition, and
free of damage and wear.
2. Uncap the Fuel Bottle by turning the cap counterclockwise. Pull cap to remove. Fill with fuel.
IMPORTANT! Never fill beyond Fill Line that is marked on fuel bottle. See Illustration 1.
3. Screw the pump snugly into the Fuel Bottle.
4. Firmly close the pump Control Valve Handle (A).
5. Pump the Plunger (G) 15-20 strokes.
Note: If the Fuel Bottle is not full, more pump
strokes are required. For example, when
half-full, about 40-55 strokes are required. In general, pump until firm resistance is felt.
6. IMPORTANT! Always check for leaking fuel. Check for leaks near every seal, including the
Pump Seal, Fuel Tube O-ring, Control Valve area, and Pump Plunger. If leaking fuel is found, DO
NOT USE STOVE. See TROUBLESHOOTING or send it to your MSR retailer or MSR Product Service
Center for repairs.
ATTACHING THE XGK STOVE TO THE PUMP
1. Lubricate the end of the Fuel Line (Q) with saliva or oil.
2. Insert the Fuel Line into the pump. See Illustration 2.
3. Snap the Catch Arm (P) securely into the slot on the pump. See Illustration 3.
4. Insert the Lower and Upper Panwires (L) into the stove. See Illustration 4.
5. Place the stove onto the Heat Reflector. See illustration 5.
OPERATING THE XGK STOVE
PREHEATING THE STOVE
The stove must be preheated or "primed" in order to operate
properly. Insufficient preheating may result in flare-ups or poor
performance.
1. Open the Control Valve and allow approximately 1/4 oz.
(1 teaspoon) of fuel to flow through the jet.
2. Close the Control Valve.
3. IMPORTANT! Check for leaking fuel. Carefully evaluate the Fuel Bottle, Pump, and Fuel Line for
leaking fuel. If leaking fuel is found, DO NOT USE STOVE. See TROUBLESHOOTING.
4. If no leaking fuel is present, light the fuel in the Burner Cup (O). See Illustration 6.
5. Place the Windscreen around the stove only. Important! Ensure that the pump and fuel bottle are
outside of the windscreen. See Illustration 5. Fold the ends of the windscreen together.