Product Characteristics; 1- Product Features; Technical Data; Preliminary Checks - Vimar Elvox ESM8 Installations- Und Benutzerhandbuch

ACTO

1. Product characteristics:

Automation system for residential and apartment block sliding gates. The non-reversible, electromechanical actuator is equipped with an asynchronous 230
V AC motor and a mechanical release which enables the gate to be opened and closed manually. The motor operates a gear unit, lubricated with permanent
grease, which is enclosed in a thick but extremely compact die-cast aluminium housing. The electronic control card is integrated in the actuator body.

2. Technical data

Description
Power supply
Absorption
Electric motor power supply
Electric motor power
Maximum gate leaf weight
Opening speed
Maximum torque
Type of use
Frequency of use
Protection rating
Operating temperature
Rack pinion
Actuator dimensions
Weight

3. Preliminary checks:

For the automation system to function properly, the structure of the existing gate, or the one to be made, must meet the following requirements:
- The wheels of the gate are mounted in such a position as to provide stability to the gate and are in a good condition and efficient.
- The rail is clear, straight and clean throughout its length with mandatory stops for both opening and closing.
- The top guide is aligned with the rail, the sliding blocks are intact and lubricated and with a clearance of approximately 1 mm. on each side so as to facilitate
the sliding of the gate leaf.
- The spaces between the moving and fixed parts of the gate are of the size required by the national standards or in any case comply with safety standards
by applying an adequate protection system
- The weight of the gate must not exceed the limits required by the actuator
- There must be no mechanical locks fitted.

4. Preparing wiring:

For the system wiring arrangements, refer to fig. 1

5. Laying the anchor plate:

The positioning of the plate must comply with the distances shown in:
- Fig. 2a for installation with the motor on the left, Fig. 2b for installation with the motor on the right
If the rack is already installed on the gate leaf:
- Fig. 2c for installation with the motor on the left, Fig. 2d for installation with the motor on the right
It is also imperative for the rack to protrude from the centre of the plate by at least the distances shown in:
- Fig. 4a (motor on left)
- Fig. 4b (motor on right)
to allow positioning the limit switch brackets.
N.B.: The foundation plate has two large holes for the conduits to pass through. Both can be used, thanks to the space on the bottom of the gearmotor, but
it is easier to use the hole to the right of the pinion, shown in grey in the figures.
Installing the anchor plate when there is no paving:
If there is no paving made of concrete or an equally resistant material that can support the stresses caused by the actuator, it is necessary to make a concrete
foundation, as follows:
1- Dig a suitable hole (minimum 50x30cm, at least 35 cm deep) (Fig. 5a).
2- Arrange the pipes for carrying the electric cables, leaving the pipes approximately 30/40cm longer (Figure 5a).
3- If the rack is pre-installed at a greater height than as shown in Fig. 2c, or if there is a likelihood of stagnating water, it may be necessary to raise the concrete
foundation or install the anchor plate raised to the appropriate height. In this case 4 extra nuts must be used (not supplied) as a base for the anchor plate.
In any case do not install the plate any higher than 15 mm above the paving.
4- Prepare the anchor plate for pouring by firmly fixing it to the threaded rods (Fig. 5b) using the 4 lower support nuts and the 4 upper nuts with their washers
to lock the plate in position.
5- Prepare the concrete according to the manufacturer's instructions, in some cases it may be necessary to make a metal cage to stabilize the foundation.
6- Sink the rods into the concrete, paying attention to the level of the plate and the parallelism with the gate leaf (Fig. 5c and 5d).
7- Wait for the concrete casting to set.
8- Fig. 5d shows the plate when fixing is completed.
10
ACTO 510A (ESM8)
1.6 A
350 W
500 kg
10 Nm
Residential and apartment blocks
9.5 kg
ACTO 810A (ESM9)
230 Vac - 50 Hz
230 Vac
9 m/min
Tertiary and industrial
30%
IP44
-20°C / +50°C
Module 4
324 x 205 x 265 (fig. 2)
1.6 A
350 W
800 kg
16 Nm
10 kg
EN