Remote Control; Maintenance; General Tips - Faber CAS500 Anleitungen

• is the reduce flame button for the left had side of the appliance. Press this to reduce the height/intensity of your
flame. You will hear an audible beep when you reach the minimum level
• is the increase flame button for the left had side of the appliance. Press this to increase the height/intensity of
your flame. You will hear an audible beep when you reach the maximum level
• is the reduce flame button for the right had side of the appliance. Press this to reduce the height/intensity of your
flame. You will hear an audible beep when you reach the minimum level
• is the increase flame button for the right had side of the appliance. Press this to increase the height/intensity of
your flame. You will hear an audible beep when you reach the maximum level

REMOTE CONTROL

The remote control is supplied with 2xAAA batteries. Remove the battery cover from the underside of the remote control
and after removing the batteries from the plastic wrapping fit them into place. Replace the battery cover.
The remote control has wireless technology and is required to be paired to the receiver. This is done by pressing the
button on Button Panel 'A', the LED's will start to blink on and off. This is to let you know that the appliance is ready to
connect to the remote control. Press the
control is paired to the appliance.
The operation of the remote control is the same as described in 'Receiver Controls'. You can pair multiple products to
the one remote control by repeating the pairing operation as above on your subsequent products.
The operation of the remote control is the same as described in 'Receiver Controls'.
Pairing to multiple products: If you are installing multiple CAS500/CAS1000 products you can pair them to one remote
control. To do this, please install the products as described in the "Installation Instructions". Please ensure that the
products are connected to mains power and have water supplied. If you are pairing CAS1000 and CAS500 products
please choose the 6 button remote control as the master remote control. Pair the first product as described in the
'REMOTE CONTROL' section above
1. On your second product press the rocker switch to the on (I) position, 1 beep
2. Press on the manual controls, 1 beep and the product will begin to start.
3. Press on the manual controls, beep and LED's start to blink.
4. Press on the remote control. The product will beep and LED's flash 5 times.
The product will automatically switch off.
5. Repeat the above steps to pair the next product.
When all products are paired, test the remote control by pressing (standby). If any of the products fail to receive a signal
from the remote control you can bring that product back in line with the others via the Manual Controls or the receiver
controls.

Maintenance

GENERAL TIPS

Only use filtered tap water in this appliance.
Always ensure that the appliance is sitting on a level surface.
If you intend not using the appliance for longer than 2 weeks, remove and empty the sump and water tank.
Once installed, never move this appliance or lay on its back, without draining the water from sump and water tank.
CLEANING
Warning – Always press Switch 'A' to the 'OFF' (0) position (Fig.6) and disconnect from the power supply before
cleaning the fire.
We recommend cleaning the following components once every 2 weeks, particularly in hard water areas:-
Water Tank, Sump, Nozzle, Tank cap and seal, Air filter.
For general cleaning use a soft clean duster – never use abrasive cleaners.
To remove any accumulation of dust or fluff the soft brush attachment of a vacuum cleaner should occasionally be used
to clean the outlet grille of the fan heater.
Water tank
1. Remove water tank, by lifting off the metal plate and set aside. Lift out the tank, place it into a sink and empty water.
2. Using a soft brush gently rub the inside surfaces of the cap paying particular attention to the rubber ring in the outer
groove and the center rubber seal.
3. Put a small quantity of washing up liquid into the tank, refit the cap and shake well, rinse out until all traces of
washing up liquid are gone.
4. Refill with filtered tap water only, replace the cap, do not over tighten.
Sump
1. Press Switch 'A' to the 'OFF' (0) position (Fig.6)
2. Gently lift out the fuelbed and place carefully on the ground
3. Remove the water tank by lifting upwards or in the case of a Mains Water, disconnect the 'fill cap' by turning it
button on the remote control. The appliance will switch off. Now the remote
21