Operating - SILENTRON Vocalphone HT series Handbuch

 Vocal Messages: direct recording on the appliance of 4 alarm messages plus one precompiled automatic for "flat internal battery"
A total of 120 second of recording.
 SMS: direct writing on the appliance of 4 alarm messages plus 6 precompiled technical SMS with automatic sending (see 8.3).
 Messages control via radio: 99 transmitters freely assignable on 4 alarm messages.
 Relay output for load control: none
6) APPLIANCES OPERATION - INFORMATION FOR THE USER
Holding into account that some models do not contemplate all the functions as described above, the appliances operate as follows:
6.1) ALARM/ASSISTANCE
When the appliance is in the sleep mode it highlights the GSM field in those models that have the function and the writing CONNECTION in
case of alarm. Following an electric control o via radio on one of the 4 messages, the appliance calls all the telephone numbers in the book
combined to an activated message. This occurs on phone net or GSM according to the models and the set priority programming.
When the called number answers, the message is repeated twice. If the called number is busy or absent the call is repeated after 3 minutes and
so on for other two times. In case of programming without line control, the message is repeated 4 times (see 8.3).
To interrupt the next calls to other users press the key
order to listen to the environment noises through the appliance press the key
relative SMS message is sent to all the numbers in the telephone book combined to the activated message.
6.2 LOAD CONTROL VIA TELEPHONE (ONLY 5150 – 5152 MODELS)
Call to the GSM module in board: it is always activated to answer to answer coming-in calls: it is necessary to listen to the instruction
message, wait for the and then type in the user's code followed by # (if the caller has a direct access it is not necessary to type in USER CODE)
Controls of the possible executions, with sound signal for every pressed key:
- type in to access the "handsfree" function that allows to listen and dialog.
- type in 1 1 # to activate the relay 1, that is deactivated typing in 1 0 #
- type in 2 1 # to activate the relay 1, that is deactivated typing in 2 0 #
- type in 1 (2) # to control the state of the relay 1 (2): the appliance answers with 3 beeps if the relay is activated, with one if the relay is
deactivated.
6.3 ACCESS TO THE HISTORY FILES (EVENTS MEMORY)
The access to the history file is made by typing in the installer/user's code followed by the
the call's outcome (OK: call had a positive outcome, NO: no reply, OC: line busy) for the last 200 calls, highlighting any absence of GSM field,
lack of traditional line, occurred modification from remote etc. The following is also reported: the indication of the going-out telephone call ( ) or
coming-in telephone call ( ) and the indication of the type of call or SMS (S) or Vocal (V).
Return to the stand-by mode is made through the ESC key, or automatically after 1 minute without operations.
6.4 REMOTE CHANGING OF TELEPHONE NUMBERS (ONLY MODELS 5150 - 5152)
By means of an SMS from a remote GSM it is possible to change the telephones numbers stored in the phone book; the number of the remote
phone must be memorized on the system with the direct access function "Y" (yes). Compile the message as follows (bold):
A333555666 (old number to replace) A333666888 (new number to insert)
The appliance memorizes the variation and sends a confirm SMS: CHANGE MADE *333666888*
6.5 CALL BLOCK ON APPLIANCE: type in the user/installer's code followed by "CANC" the coming-in calls are blocked.
6.6 REQUEST FOR REMAINING SIM CREDIT (ONLY 5150 - 5152)
Pressing the key for 2 seconds the automatic call to the provider is made for information on the remaining credit on the SIM that is listened
directly on the appliance.

7) OPERATING

Install every telephone transmitter opportunely hidden where used in alarm systems. It is necessary to verify the presence of a GSM field in the
models with this function before fixing the appliance to the wall, placing another mobile phone that uses the same provider in the exact place
where the appliance will be fixed.
SMS enabling: for the models with GSM it is necessary to eliminate the PIN code or replace it with the numbers 1,2,3,4; to enable the SIM
before using it in the appliances and assess that it has a minimum residual credit: a non-validated SIM, out of order or missing does not allow ur
the appliance to function. Attention! Introduce the SIM to a NON POWER SUPPLIED appliance!
Electric connections: to carry out the electric connections requested by the appliance (see drawing) considering the functioning of the IN-OUT
connections. The control in-outs must be closed on GND (negative) and the transmission are activated by opening. The in-puts of the closed
blocks in POSITIVE block the telephone transmission. The two TAMPER terminals give a closed circuit when the box completely closed (anti-
opening protection of the cover and anti-removal on the bottom). The outlet +OUT is "open collector" and closes by GND for an absence of
GSM field of over 15 minutes (only models 5150-5152).
The relay outputs, present only on models 5150-5152, have a free potential exchange contact in free exchange with a maximum capacity of
500mA at 12V CC. The relay works in a bistable way upon call to the appliance (see
WARNING ! The devices 5150-5152 work at 12V DC with backup battery 6V 1,2 Ah, which is compulsory to provide the necessary
power supply to the GSM module during the transmission. The connection to different voltage rates and/or different backup batteries
damages the device irremediably, with consequent warranty loss.
connected the primary power supply.
The 5590 model works at 6V DC with 4 alkaline batteries type D (torch). It is available on demand a model with a feeder.
WARNING ! Between the control panel (any type) and the Vocalphone, the mass (GND - negative pole) must be common.
on your telephone after the end of message beep: the appliance will stop the calls. In
on your telephone after the end of message beep. However the
The backup battery has always to be connected after having
key. The history file has the date, called name and
10