Using Accessories - Polti Forzaspira CS200 Gebrauchsanweisung

CORRECT USE OF THE PRODUCT
This appliance is intended for home use for vacuu-
ming solids as described and in accordance with
the instructions provided in this manual. Please
read these instructions carefully and keep them, as
you may find them useful in future.
Polti declines liability for any damage or acci-
dent derived from any use of this appliance whi-
ch does not comply with the instructions con-
tained in this booklet.
ATTENTION
Directive 2011/65/UE (Waste Electrical and Electro-
nic Equipment - WEEE): information for users
This product complies
2011/65/UE.
The crossed-out wastebasket symbol on
the appliance means that at the end of its
useful lifespan, the product must be di-
sposed of separately from ordinary hou-
sehold wastes.
The user is responsible for delivering the appliance
to an appropriate collection facility at the end of its
useful lifespan.
Appropriate separate collection to permit recycling,
treatment and environmentally compatible disposal
helps prevent negative impact on the environment
and human health and promotes recycling of the
materials making up the product. For more informa-
tion on available collection facilities, contact your lo-
cal waste collection service or the shop where you
bought this appliance.
PREPARATION/USE
♦ Remove the appliance from the packaging,
checking that the product is whole and that all
the parts are there.
♦ Insert the suction opening (A3) of the flexible
hose (A) into the connection (2), and turn it
clockwise (Fig. 1). To remove it from the ap-
pliance, turn the suction opening of the flexible
hose (A) anti-clockwise (Fig. 2) and pull it out.
♦ Unwind the power supply cable (11) and insert
the plug into a suitable power socket.
♦ Press the ON/OFF switch (7) (Fig. 3) to start suc-
tion.
♦ To adjust suction, turn the knob (6) to the desired
position (Fig. 4). We suggest minimum level for
curtains, medium-low for filled furniture and high
for floors and hard surfaces (ceramic, marble
etc.).
FORZASPIRA CS200
with EU Directive
16
♦ With the manual suction regulator (A2) it is possi-
ble to intervene promptly in case of accidental
suction (i.e. curtains), reducing the suction power.
Move the regulator to uncover the hole located on
the handle, thus reducing suction (Fig. 5).
♦ To end suction, press the ON/OFF switch again (7).
ACCESSORIES HOLDER
The lance (D) and the bristle nozzle (F) are kept in
the accessory holder. To access it, press the button
(3) and lift the lid (4) (Fig. 6).

USING ACCESSORIES

Accessories may be connected directly to the hose
(A) or to the telescopic tube (B) (Fig. 7-8).
Using the telescopic tube (B)
The length of the telescopic tube can be adjusted
by pressing the button (B1) in the direction of the
arrow.
Using the universal brush (C)
Connect the brush to the telescopic tube (B).
To vacuum hard floors, use the switch (C2) to select
the bristles-extended position.
To vacuum rugs and carpeting use the switch (C2)
to select the no-bristles position.
Lance (D)
This lance is suitable for thorough cleaning of the
more difficult-to-reach places, like skirting-boards,
sofa gaps, armchairs, upholstered furniture, car
seats.
Bristle nozzle (F)
The small nozzle is recommended for removing
dust from upholstered surfaces such as the joints of
sofas, armchairs, mattresses, car upholstery, etc.
AUTOMATIC CABLE WINDER
Before starting the automatic cable rewind, using the
button (10), make sure that the power plug is discon-
nected from the mains. We recommend guiding the
cable during this operation.
PUTTING THE APPLIANCE AWAY
It is possible to replace the appliance by resting the
brush (G) with the tube (B) in the parking housing (9)
(Fig. 10-11).