Inglesina zippy free Benutzerhandbuch Seite 38

CAUTION: Hold the supports during the ejec-
tion.
Fig. 42 Remove the armrest covers X, if available,
by pressing with the index fi nger the hooking lever
O positioned inside the armrest R.
Fig. 43 By holding the Seat by the handle, attach
it to the Frame on the armrests R, positioning it ex-
clusively facing mum.
Fig. 44 CAUTION: Make sure that the Seat is
always properly hooked before use.
UNHOOKING OF THE CAR SEAT FROM THE
FRAME
Fig. 45 Act on the lever Z positioned on the rear
side of the Seat.
Fig. 46 Simultaneously, lift the Seat by holding it
by the handle.
To use the Huggy Car Seat properly, refer to the de-
dicated manual.
TRANSPORT SEAT
HOOKING OF THE TRANSPORT SEAT TO THE
FRAME
Before hooking the Transport Seat to the Frame:
Fig. 47 If present, remove the stabilizing sup-
ports P by acting on the proper push-buttons V.
CAUTION: Hold the supports during the ejection.
Fig. 48 Insert the armrest covers X in the proper
seats.
CAUTION: When placing the baby, make always
sure that the armrest covers are properly fi tted
in their seats.
Fig. 49 The Transport Seat is reversible; there-
fore, it can be hooked to the Frame facing mum or
the street.
Fig. 50 Hook the Transport Seat to the Frame
positioning it in the proper seats on both sides,
following the graphical references available on the
structure.
Fig. 51 CAUTION: Make sure that the Trans-
port Seat is always properly hooked on both si-
des before use.
UNHOOKING OF THE TRANSPORT SEAT FROM
THE FRAME
Fig. 52 Press the lever W and lift one side of the
Transport Seat by moving it slightly inwards. Repeat
this procedure on the opposite side, removing it
completely.
CAUTION: Never perform this procedure with
baby on board.
38
INSTRUCTIONS
ADJUSTMENT OF THE BACKREST
Fig. 53
positions; act on the central device Y and bring the
backrest to the wished position.
USE OF THE HANDRAIL
Transport seat facing mum
Fig. 54
use the small handrail J together with its covering.
Fig. 55
Fig. 56
proper seats B1 on the Transport Seat.
Fig. 57
or completely removed. To open it, press the lever
A1 and extract it; to remove it, repeat the procedure
also on the other side.
Transport seat facing the street
Fig. 58
street, use the big handrail C1 together with its co-
vering.
Fig. 59
on the armrests and press them until they block.
Fig. 60
or completely removed. To open it, press the red le-
ver D1 present under the armrest R; to remove it,
repeat the procedure also on the other side.
CAUTION: Do not insert the fi ngers in the ope-
nings on the armrests when performing these
procedures.
HOOD
Fig. 61
seats on the sides of the Transport Seat and hook
the buttons to the structure.
Fig. 62
The Hood covering can be removed to allow its cor-
rect maintenance.
Fig. 63
both sides of the Hood articulated joints F1.
Fig. 64
from the rods G1 and extract the covering comple-
tely.
Fig. 65
rods G1 in the proper guides on the internal lining.
Fig. 66
seats on both articulated joints F1, until they are
completely hooked.
Fig. 67
the articulated joints F1 must always be positio-
ned on the front.
It is possible to adjust the backrest to 4
When the Transport Seat is facing mum,
To hook it, press the levers A1.
Insert the ends of the handrail in their
The handrail can be opened on one side
When the Transport Seat is facing the
To hook it, insert the ends in the openings
The handrail can be opened on one side
Insert the ends of the Hood in the proper
To remove the Hood, simply extract it.
Unhook the buttons E1 positioned on
Then, unhook both articulated joints F1
To reassemble the covering, insert both
Then, insert the rods G1 in the proper
CAUTION: The curved insertion part of