Parkside PKZS 2000 A1 Bedienungs- Und Sicherheitshinweise Seite 52

• Use the handle (1) to push back the machine head (4) and
fix it in this position if required (dependent on the cutting
width).
• Place the piece of wood to be cut at the stop rail (16) and
on the turntable (14).
• Lock the material with the clamping devices (7) on the
fixed saw table (15) to prevent the material from moving
during the cutting operation.
• Push down the release lever (3) to release the machine
head (4).
• Press the ON/OFF switch (2) to start the motor.
• With the drag guide (21) fixed in place:
use the handle (1) to move the machine head (4) steadily
and with light pressure downwards until the saw blade
(6) has completely cut through the work piece.
• With the drag guide (21) not fixed in place:
pull the machine head (4) all the way to the front. Lower
the handle (1) to the very bottom by applying steady and
light downward pressure. Now push the machine head
(4) slowly and steadily to the very back until the saw
blade (6) has completely cut through the work piece.
• When the cutting operation is completed, move the ma-
chine head back to its upper (home) position and release
the ON/OFF button (2).
Attention! The machine executes an upward stroke
automatically due to the return spring, i.e. do not release
the handle (1) after completing the cut; instead allow the
machine head to move upwards slowly whilst applying
light counter pressure.
8.4 Cross cut 90° and turntable 0° - 45° (Fig. 9)
The crosscut, drag and mitre saw can be used to make cross-
cuts of 0° - 45° to the left and 0° - 45° to the right in relation
to the stop rail.
Important. To make 90° crosscuts, the adjustable stop rail
(16a) must be fixed at the inner position.
• Open the set screw (16b) for the adjustable stop rail (16a)
and push the adjustable stop rail (16a) inwards.
• The adjustable stop rail (16a) must be fixed far enough in
front of the innermost position that the distance between
the stop rail (16a) and the saw blade (6) amounts to a
maximum of 8 mm.
• Before making a cut, check that the stop rail (16a) and the
saw blade (6) cannot collide.
• Secure the set screw (16b) again.
• Loosen set screw (26).
• Use the handle (11) to adjust the rotary table (14) to the
desired angle. The pointer (12) on the rotary table must
match the desired angle on the scale (13) on the fixed saw
table (15).
• Re- tighten the set screw (26) in order to secure the rotary
table (14).
• Cut as described under section 8.3.
8.5 Precision adjustment of the stop for mitre cut 45°
(Fig. 1/6/10/11)
• No stop angle included.
• Lower the machine head (4) and secure using the locking
bolt (23).
• Fix the rotary table (14) in the 0° position.
• Loosen the set screw (22) and use the handle (1) to angle
the machine head (4) 45° to the left.
• 45° - position angle stop (b) between the saw blade (6)
and rotary table (14).
• Adjust the adjusting screw (28) until the angle between the
saw blade (6) and rotary table (14) is precisely 45°.
• It is not necessary to fix this setting because it is maintained
by the spring pretension.
• Subsequently check the position of the angle indicator. If
necessary loosen the pointer (19) using a Philips screw-
driver, set to position 45° on the angle scale (18) and re-
tighten the retaining screw.
8.6 Mitre cut 0°- 45° and turntable 0° (Fig. 1/2/12)
The crosscut, drag and mitre saw can be used to make mitre
cuts of 0° - 45° in relation to the work face.
Important! To make miter cuts (inclined saw head), the ad-
justable stop rail (16a) must be fixed at the outer position.
• Open the set screw (16b) for the adjustable stop rail (16a)
and push the adjustable stop rail (16a) outwards.
• The adjustable stop rail (16a) must be fixed far enough in
front of the innermost position that the distance between
the stop rail (16a) and the saw blade (6) amounts to a
maximum of 8 mm.
• Before making a cut, check that the stop rail (16a) and the
saw blade (6) cannot collide.
• Secure the set screw (16b) again.
• Move the machine head (4) to the top position.
• Fix the rotary table (14) in the 0° position.
• Loosen the set screw (22) and use the handle (1) to angle
the machine head (4) to the left, until the pointer (19) in-
dicates the desired angle measurement on the scale (18).
• Re- tighten the fixing screw (22).
• Cut as described in section 8.3.
8.7 Mitre cut 0°- 45° and turntable 0°- 45°(Fig. 2/4/13)
The crosscut, drag and mitre saw can be used to make mitre
cuts to the left of 0°- 45° in relation to the work face and, at
the same time, 0° - 45° to the left or 0° - 45° to the right in
relation to the stop rail (double mitre cut).
Important! To make miter cuts (inclined saw head), the ad-
justable stop rail (16a) must be fixed at the outer position.
• Open the set screw (16b) for the adjustable stop rail (16a)
and push the adjustable stop rail (16a) outwards.
• The adjustable stop rail (16a) must be fixed far enough in
front of the innermost position that the distance between
the stop rail (16a) and the saw blade (6) amounts to a
maximum of 8 mm.
• Before making a cut, check that the stop rail (16a) and the
saw blade (6) cannot collide.
• Secure the set screw (16b) again.
• Move the machine head (4) to its upper position.
• Release the rotary table (14) by loosening the set screw
(26).
• Using the handle (11), set the rotary table (14) to the de-
sired angle (refer also to point 8.4 in this regard).
• Re- tighten the set screw (26) in order to secure the rotary
table.
• Undo the locking screw (22)
GB/MT 47