Jacuzzi J-300 series Montageanweisung Und Bedienung Und Wartung Seite 36

WARNING: RISK OF ELECTRICAL SHOCK HAZARD
EXISTS AND EQUIPMENT DAMAGE! Never install or re-
move electrical devices (e.g. iPod/MP3/USB/AUX/Bluetooth)
while hands are wet or while sitting partially or fully immersed in
the spa!
CAUTION: Never leave electrical devices in the Media Locker
when spa is not is use to prevent damage from outdoor elements!
Never spray Media Locker with a pressurized water hose for
any reason! Damage to the device or spa stereo system caused
by water intrusion is not covered under the manufacturer's war-
ranty! Damage to Media Locker port or electrical devices due to
excessive force or improper alignment during installation or re-
moval from Media Locker is not covered under warranty.
Pairing the Remote and Stereo
In order for the remote to operate the stereo, you need to pair
them using the following method:
- Make sure the stereo unit is OFF. LED power light will be off.
- Press any button on the remote to turn it ON. The remote L-
CD display will read "No Link. "
- Press and hold the "Mode" button on the remote. At the same
time, press and hold the power button on the stereo for 2 sec-
onds.
- The remote LCD display will read "Welcome, " "Load" and "Ra-
dio" if the pairing sequence was successful.
Audio Settings
The Audio button, provides access to many of the stereo's set-
tings. By continually pressing the Audio button you can scroll and
adjust the following functions: BAS-TRE-BALFAD-DSP-AREA-
LOUD-DX-STEREO (respectively).
Note: You can adjust the settings by pressing the Audio but-
ton, making your adjustments and pressing the Audio button
to go the next feature. If you exit the setting menus continu-
ally press the Audio button until you reach the setting you
would like to adjust.
Bass Setting
Press the Audio button once to access the bass setting. The L-
CD display will change to "BAS 0, " . Press the Up button to ad-
just the setting to a maximum of +7. Press the Down button to
adjust the setting down to -7.
Note: The default setting is "0." This feature is disabled when
a "Digital Sound Processor" (DSP) setting is active such as
"Rock," "Classical," or "Pop."
AUDIO MODE
1 2 3
36
Treble Setting
Press the Audio button 2 times to access the treble setting. The
LCD display will change to "TRE 0, " . Press the Up button to ad-
just the setting to a maximum of +7. Press the Down button to
adjust the setting down to -7.
Note: The default setting is "0." This feature is disabled when
a "Digital Sound Processor" (DSP) setting is active such as
"Rock," "Classical," or "Pop."
Balance Setting
Press the Audio button 3 times to access the balance setting. The
LCD display will change to "BAL L=R, " . Press the Up button to ad-
just the setting to a maximum of 10R (only the right side speak-
ers will have volume). Press the Down button to adjust the setting
down to 10L (only the left side speakers will have volume).
Fade Setting
Press the Audio button 4 times to access the fade setting. The
LCD display will change to "FAD F=R, " . Press the Up button to
adjust the setting to a maximum of 10F (only the front speak-
ers will have volume). Press the Down button to adjust the set-
ting down to 10R (only the rear speakers will have volume).
Digital Sound Processor (DSP) Setting
Press the Audio button 5 times to access the DSP setting. The
LCD display will change to "DSP OFF, " . Press the Up button to
select one of the preset settings such as Rock, Classical or Pop.
If a preset setting is select a small icon will appear
ROCK
on the LCD display.
Area Setting
Press the Audio button 6 times to access the Area setting. The
LCD display will change to "AREA USA, " . Press the Up button to
select either USA or EUR setting.
Loud Setting
Press the Audio button 7 times to access the Loud setting. The
LCD display will change to "LOUD OFF, " . Press the Up button to
select either OFF or ON.
Distant Setting
Press the Audio button 8 times to access the Distant setting. The
LCD display will change to "DX, " . Press the Up button to select ei-
ther Distant (DX) or Local for station frequency. The "LOCAL" set-
ting allows for better FM reception when a local station is too
strong. Leave the setting to "DX" if this condition does not exist.
Stereo Setting
Press the Audio button 9 times to access the Stereo setting. The
LCD display will change to "STEREO, " . Press the Up button to
select either Stereo or Mono.