Werbung
Verfügbare Sprachen
Verfügbare Sprachen
1 COMPONENTS
2 APP INSTALLATION
To download the mobile application please use below methods of installation:
Search for the latest mobile application on our official website (www.aee.com).
Scan the QR code and follow the instructions to download and install the AEE ZONE mobile application onto your mobile
device.
Search for "AEE ZONE" in the Apple appstore or Google Play store, download and install the "AEE ZONE" mobile
application.
Compatible with iOS 8.0 and above, iPhone 5 devices and later.
Compatible with Android 4.0 and above, all dominant Android devices.
3 CHARGING
The battery level is indicated by the battery level icon on the APP. Follow the illustration below to charge the battery when the battery level
icon shows less than one bar of power.
To charge battery, insert the USB cable to the appropriate port on the charging base.
Blue: charging status indicator
Flash slowly: charging
Remain on: fully charged
Flash: no battery or damaged battery
Note:
Over-discharging may shorten the battery's life severely. Please charge the battery in time.
Limit each charging to 2 hours maximum.
4 SD CARD INSTALLATION
Insert SD card into the card slot as below.
Note:
1. To use the video/photo function, a SD card must be inserted before powering on the drone.
2. SD card Max 64G, Class Ultra 1 or above.
5 BATTERY INSTALLATION
1. Motor(s) and Propeller(s)
2. Aircraft Battery
3. Landing Gear(s)
4. Infrared Sensor(IR) for
Obstacle Avoidance
5. Aircraft Camera
6. Power Button
7. Micro USB Port
8. Micro-SD Card Slot
9. Optical Flow Module
(Undercarriage)
Insert the battery into the battery compartment as directed by the 8 pins
as shown in left figure.
6 APP CONNECTION
-
Enable Wi-Fi functionality on your mobile device.
-
Connect to the Wi-Fi hotspot named "AEE_SPARROW_XXXXXXX".
-
Start the AEE ZONE application, select the Sparrow 360 as your device and tap on "Connect".
-
Press and hold the Sparrow 360 power button for 3 seconds.
-
If the power button light comes on solid without flashing, the aircraft has been successfully connected to your mobile device and is now
ready for use.
Step 1: Turn "ON" the Wi-Fi function of your mobile device and connect
to the Wi-Fi hotspot named "AEE_SPARROW_XXXXXXX" as shown in figure
. Enter the password "00000000" to connect.
Step 2: Open the AEE ZONE mobile application and select the SPARROW
device. Tap on "Connect" as shown in figure
. The application will
now take you to the flight user interface as shown in figure
Step 3: Tap the REC BUTTON
as shown in fi gure
.
Step 4: Select an Intelligent Mode as shown in fi gure
.
7 MAIN INTERFACE
8 CALIBRATION
.
1.
Return the home page
2.
Flash on/o
3.
Headless mode on/o
4.
Select remote control mode: motion mode
or joystick mode
5.
IR sensor on/o
6.
Quick take o /landing
7.
Select a shooting/recording mode: 4
modes available
8.
Start shooting/recording
9.
Head mode switch
10.
Library
11.
Settings
12.
Battery level
13.
Wi-Fi signal
Generally the drone is automatically calibrated with initial connection to the
AEE ZONE APP. However, please calibrate it if the drone deflects or shakes.
Place the drone in normal condition on the ground horizontally and power it on.
1. Start AEE ZONE connected to the drone, tap the remote control icon
,and select the joystick mode to enter the following interface:
2. Pull the joysticks down as shown below. When power light flashes on the
drone, release the joysticks.
3. Wait about 20 seconds until the power light is a steady "On" with no
flickering. This means the calibration is successful. If not successful,
shut down the drone, remove the battery, and reinsert the battery and
calibrate again following steps 1. & 2. and observing the results about 20
seconds later as noted above.
Werbung
