Specifications; General Safety Rules - Makita 5603R Betriebsanleitung

ENGLISH
1 A typical illustration of proper
hand support, workpiece sup-
port, and supply cord routing (if
applicable).
2 To avoid kickback, do support
board or panel near the cut.
3 Don't support board or panel
away from the cut.
4 Hex wrench
5 Shaft lock
6 Tighten
7 Loosen
8 Saw blade

SPECIFICATIONS

Model
Blade diameter .............................................................................165 mm
Max. cutting depth
At 90° ........................................................................................ 54 mm
At 45° ........................................................................................ 38 mm
–1
No load speed (min ) ................................................................. 5,000
Overall length .............................................................................. 330 mm
Net weight ................................................................................... 4.2 kg
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
For model 5705R, public low-voltage distribution
systems of between 220 V and 250 V
Switching operations of electric apparatus cause voltage
fluctuations. The operation of this device under unfavor-
able mains conditions can have adverse effects to the
operation of other equipment. With a mains impedance
equal or less than 0.36 Ohms it can be presumed that
there will be no negative effects. The mains socket used
for this device must be protected with a fuse or protective
circuit breaker having slow tripping characteristics.

GENERAL SAFETY RULES

WARNING! Read all instructions. Failure to follow all
instructions listed below may result in electric shock, fire
and/or serious injury. The term "power tool" in all of the
warnings listed below refers to your mains-operated
(corded) power tool or battery-operated (cordless) power
tool.
6
Explanation of general view
9 Outer flange
10 Inner flange
11 Hex socket head bolt
12 Saw blade
13 Setting protuberances
14 Hex socket head bolt
(For adjusting riving knife)
15 Cutting depth
16 Loosen
17 Lever
18 Thumb nut
19 For 45° bevel cuts
20 For straight cuts
Work area safety
1.
2.
3.
Electrical safety
4.
5.
6.
GEA001-3
7.
8.
21 Base plate
22 45° angle cuts
23 Straight cuts
24 Top guide
25 Base
26 Lock-off button
27 Switch trigger
28 Vacuum cleaner
29 Limit mark
30 Brush holder cap
31 Screwdriver
5603R 5705R
190 mm
66 mm
46 mm
4,800
356 mm
5.2 kg
SAVE THESE INSTRUCTIONS.
Keep work area clean and well lit. Cluttered and
dark areas invite accidents.
Do not operate power tools in explosive atmo-
spheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
Keep children and bystanders away while oper-
ating a power tool. Distractions can cause you to
lose control.
Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
Do not expose power tools to rain or wet condi-
tions. Water entering a power tool will increase the
risk of electric shock.
Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords
increase the risk of electric shock.
When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of
electric shock.
5903R
235 mm
85 mm
64 mm
4,500
400 mm
7.0 kg