Programming Of Positions; A - Manual Programming Of Positions "0", "1" And "I; B - Automatic Programming Of The Positions "0" And "1 - Nice TTPRO BD Installations- Und Bedienungsanleitung

02. Press the button with the desired direction:
03. ➔ The green OK LED flashes: (within 3 sec) press the OK button to confirm.
When the operation terminates, the LED on the button corresponding to the cho-
04.
sen direction will be turned on.
Note: at the end of this programming verify if the transmitter Ascent button commands
opening of the roller shutter (or the ascent of the awning), and the Descent button com-
mands the closing of the roller shutter (or the descent of the awning). If the direction is
not the desired one, repeat this procedure to programme the other direction.

3.5.2 - PROGRAMMING OF POSITIONS

Motors with electronic limit switches have functions to programme the positions: "0"
(rolling shutter or awning all rolled up), "1" (rolling shutter or awning all unrolled) and "I"
(rolling shutter or awning in an intermediate position). If a position is already stored, the
corresponding LED will be lit, otherwise a short flash indicates that the position has not
been programmed.
In the menu used to program the positions "0", "1" and "I", you can move the motor in
"hold-to-run" mode, thus enabling fine adjustment of the set position. This adjustment is
limited by the limit positions (upper limit for the upper limit switch and lower limit for the
lower limit switch). If you need to move beyond these positions, you must cancel the limit
positions and memorise them anew.

3.5.2.A - Manual programming of positions "0", "1" and "I"

The positions must be stored in the following order: "0", "1" and "I".
The memorisation procedure may vary depending on the type of motor used. Therefore,
refer to the technical specifications which are also available on www.niceforyou.com
site, with details and specific examples for each type of motor.
• Programming position "0"
Use the or button to bring the roller shutter/awning to the "0" position
01.
desired.
Press the button : the LED on the button flashes.
02.
03. ➔ The green OK LED flashes: (within 3 sec) press the OK button to confirm.
When finished, the LED on the button
04.
Notes • The direction of movement associated with the button may be not correct until
position "1" is stored. • In some types of motors, changing position "0" could erase
positions "0" and "I".
• Programming position "1"
Use the or button to bring the roller shutter/awning to the "1" position
01.
desired.
Press the button : the LED on the button flashes.
02.
AUTO
or .
DRY DRY
CONT.
CONT.
AUTO
turns on with a steady light.
AUTO
03. ➔ The green OK LED flashes: (within 3 sec) press the OK button to confirm.
When finished, the LED on the button
04.
Note: changing position "1" erases position "I".
• Programming position "I"
Use the or button to bring the roller shutter/awning to the intermediate
01.
position "I" desired.
. The key's led with flash, the OK led will flash GREEN and the level led
Press
AUTO
will indicate the number of configurable intermediate positions:
- steady red is the position being configured
- dim steady red indicates a previously configured position
- dim flashing red indicates a position which has not yet been set and which is
available for configuration.
02.
to recall the selected intermediate position if it has already been set.
Press
This facilitates visual verification of the level set at the intermediate position in
question.
or to move the motor "hold-to-run" mode to finely adjust the previ-
Press
ously configured positions.
03.
➔ Press OK to confirm the position. The OK led is steady green.
When finished, the LED on the button
04.
➔ The green OK LED flashes: (within 3 sec) press the OK button to confirm.
05.
When finished, the LED on the button
06.
Note: you cannot store position "I" if the "0" and "1" positions have not been stored
previously. • If the motor is configured for TWO-WAY communications, and only for
previously configured positions, pressing
the motor (for around 10 seconds) to pair a key on any remote control to the position
selected in the TTPRO BD.
3.5.2.B - Automatic programming of positions "0" and "1"
In some motors for roller shutters, with electronic limit switches, there is a procedure that
automatically detects positions "0" and "1". If this feature is available, after TTPRO BD
switches on the LED on the button
AUTO
To perform this procedure there must be present on the application the caps on ascent
and/or burglar springs on descent. For more details refer to the motor instructions.
.
01. Press the button
AUTO
02. ➔ The green OK LED flashes: (within 3 sec) press the OK button to confirm.
03. The motor emits 2 beeps (= start of the procedure).
turns on with a steady light.
AUTO
turns on with a steady light.
AUTO
turns on with a steady light.
AUTO
followed immediately by OK enables
DRY
CONT.
flashes.
English – 6