Layout; Supplied Package; Proper Use; Technical Data - Parkside PDS 120 A1 Originalbetriebsanleitung

3. Layout (Figs. 1-12)
1
Blow-off device
2
Mounting
3
Knurled screw
4
Holder
5
Saw blade guard
6
Saw table
7
Cover, left
8
Bearings
9
Tightening lever
10
Arm
11
Graduated scale
12
Locking lever
13
Extractor connection
14
ON/OFF switch
15
Speed regulator
16
Assembly points
17
Sawblade
18
Retaining device
19
Upper saw blade clamping screw
20
Allen key, 3 mm
21
Angle (Not supplied)
22
Storage box for saw blades
23
Lower saw blade clamping screw
24
Saw blade holder, top
25
Saw blade holder, bottom
26
Table insert
27
Pointer
28
Screw
29
Bracket
30
Work lamp
31
ON / OFF switch work lamp

4. Supplied package

• Open the packaging and take out the equipment with
care.
• Remove the packaging material and any packaging and/
or transportation braces (if available).
• Check to see if all items are supplied.
• Inspect the equipment and accessories for transport dam-
age.
• If possible, please keep the packaging until the end of the
guarantee period.
IMPORTANT
The equipment and packaging material are not toys. Do
not let children play with plastic bags, foils or small parts.
There is a danger of swallowing or suffocating!
• Fretsaw
• Saw blade guard
• Blow-off device
• Spare saw blade (2x) (for wood and plastics)
• Allen key, 3 mm
• Original operating instructions

5. Proper use

The fretsaw was designed to cut square-edged timber or
other workpieces such as Plexiglas, glass fiber reinforced
plastic, foam, rubber, leather, and cork. Do not use this saw
to cut round materials. Round materials can easily become
jammed. Risk of injury! Parts can be catapulted!
The equipment may only be used for the tasks it is designed
to handle. Any other use is deemed to be a case of misuse.
The user/operator and not the manufacturer will be liable for
any damage or injuries of any kind caused as a result of this.
Please note that our equipment has not been designed for
use in commercial, trade or industrial applications. Our war-
ranty will be voided if the equipment is used in commercial,
trade or industrial businesses or for equivalent purposes.
• The equipment is to be operated only with suitable saw
blades. It is prohibited to use any type of cutting-off wheel.
• To use the equipment properly you must also observe
the safety information, the assembly instructions and the
operating instructions to be found in this manual.
• All persons who use and service the equipment have to be
acquainted with these operating instructions and must be
informed about the equipment's potential hazards.
• It is also imperative to observe the accident prevention
regulations in force in your area.
• The same applies for the general rules of health and safety
at work.
• The manufacturer will not be liable for any changes made
to the equipment nor for any damage resulting from such
changes.
Residual risks
Even if you use this electric power tool in accordance to
instructions, certain residual risks cannot be eliminated.
The following hazards may arise in connection with the
equipment's construction and layout:
• Lung damage if no suitable protective dust mask is applied
• Damage to hearing if no suitable ear protection is applied
• Contact with the blade in the uncovered cutting zone
• Injuries (cuts) when changing the blade
• Crushed fingers
• Kickback
• Tilting of the workpiece due to inadequate support
• Touching the blade
• Catapulting of pieces of timber and workpieces

6. Technical data

Mains voltage: 220-240 V ~ /50 Hz
Power input: 80 W (S1)
120 W (S6 30%)
Stroke rate: 500 - 1,700 rpm
Protection type: IP 20
Stroke: 12 mm
Base area: 630 x 295 mm
Tilting range of table: 0° to 45° to the left
Table size: 415 x 255 mm
Length of saw blade approx.:
Reach:
134 mm
406 mm
GB 10