Hilti SIW 9-A22 Original Bedienungsanleitung Seite 21

▶ Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature
above 130° C (265 °F) may cause explosion.
▶ Follow all charging instructions and do not charge the battery pack or tool outside the temperature
range specified in the instructions. Charging improperly or at temperatures outside the specified range
may damage the battery and increase the risk of fire.
Service
▶ Have your power tool serviced by a qualified repair person using only identical replacement parts.
This will ensure that the safety of the power tool is maintained.
▶ Never service damaged battery packs. Service of battery packs should only be performed by the
manufacturer or authorized service providers.
2.2 Additional safety precautions for screwdrivers
Personal safety
▶ Only use the product if it is in perfect working order.
▶ Never tamper with or modify the tool in any way.
▶ Use the auxiliary grip supplied with the tool. Loss of control can cause personal injury.
▶ Always hold the power tool with both hands on the grips provided. Keep the grips clean and dry.
▶ Hold the power tool by the insulated gripping surfaces when performing an operation where the accessory
tool may come into contact with concealed wiring. If the accessory tool comes into contact with a live
wire, metal parts of the power tool may also become live, causing the operator to receive an electric
shock.
▶ Avoid touching rotating parts – risk of injury!
▶ Wear suitable protective glasses, a hard hat, ear protection, protective gloves and light respiratory
protection while using the tool.
▶ Wear protective gloves also when changing the accessory tool. Touching the accessory tool presents a
risk of injury (cuts or burns).
▶ Wear eye protection. Flying fragments present a risk of injury to the body and eyes.
▶ Before starting work, check the hazard class of the dust that will be produced when working. Use
an industrial vacuum cleaner with an officially approved protection class in compliance with the locally
applicable dust protection regulations. Dust from materials such as lead-based paint, certain types of
wood and concrete/masonry/stone containing quartz, minerals or metal may be harmful to health.
▶ Make sure that the working area is well ventilated and, where necessary, wear a respirator appropriate
for the type of dust generated. Contact with or inhalation of dust may cause allergic reactions and/or
respiratory or other diseases to the operator or bystanders. Certain kinds of dust, such as oak and beech
dust, are classified as carcinogenic, especially in conjunction with additives for treating wood (chromate,
wood preservative). Materials containing asbestos may only be handled by specialists.
▶ Take breaks between working and do physical exercises to improve the blood circulation in your fingers.
Exposure to vibration during long periods of work can lead to disorders of the blood vessels and nervous
system in the fingers, hands and wrists.
Electrical safety
▶ Before starting work, check the working area for concealed electric cables or gas and water pipes. If
you damage an electric cable accidentally, external metal parts of the power tool may become live and
present a risk of electric shock.
Careful handling and use of power tools
▶ Switch the power tool off immediately if the accessory tool jams. The power tool may go off course and
veer to the side.
▶ Wait until the power tool has come to a complete stop before setting it down.
2.3 Battery use and care
▶ Observe the special regulations and instructions applicable to the transport, storage and use of Li-ion
batteries.
▶ Do not expose batteries to high temperatures, direct sunlight or fire.
▶ Do not disassemble, crush or incinerate batteries and do not subject them to temperatures over 80 °C.
▶ Do not use or charge batteries that have suffered mechanical impact, have been dropped from a height
or show signs of damage. In this case, always contact your Hilti Service.
▶ If the battery is too hot to touch it may be defective. In this case, place the product in a non-flammable
location, well away from flammable materials, where it can be kept under observation and allowed to
cool down. In this case, always contact your Hilti Service.
*2113608*
Printed: 18.02.2019 | Doc-Nr: PUB / 5467491 / 000 / 01
2113608 English 15