Parkside PZKS 1500 B2 Originalbetriebsanleitung Seite 16

Attachment and operation
- Attach the miter lock handle (10) to the
turntable (15).
- When fixing the saw to the workbench,
insert the mounting screws (not included)
through the mounting holes (16a).
• In order to adjust the turntable (15)
loosen the mitre lock handle (10) approx.
2 turns.
• Press the mitre detent lever (11) and turn
the turntable (15) and pointer (12) to the
desired angle measurement on the scale
(14), release the mitre detent lever (11)
and secure with the mitre lock handle
(10).
• Pressing the machine head (4) lightly
downwards and removing the fastening
bolt (30) from the motor bracket at the
same time disengages the saw from the
lowest position.
• Swing the machine head (4) up until the
release lever (3) latches into place.
• It is possible to secure the clamping
device (7) to the left or right on the
stationary saw bench. Insert the clamping
device (7) in the hole on the rear side of
the stop rail (17) and secure it with the
grip screw (28).
• Attach the workpiece supports (8) to the
fixed saw table (16) as shown in Figure
5 and fasten with the screw (29).
• It is possible to tilt the machine head (4)
a max. 45° to the left by loosening the
locking screw (27).
8.2 Mitre angle setting
• Nine positive miter detents are provided
for fast and accurate preset miter angles
– locations are at 45°, 30°, 22.5°, 15°
left and right, and center at 0°.
• Follow the process for mitre angle setting.
• Unlock the turntable by turning the mitre
lock handle (10) counter-clockwise.
• Move the turntable while press the mitre
detent lever (11) to align the mitre angle
pointer (12) to the desired degree on the
mitre angle scale (14).
• If the desired angle is one of the nine
positive mitre detents, release the mitre
detent lever (11), making sure the lever
snaps into position, and then secure by
tightening the mitre lock handle (10).
• If the mitre angle desired is not one of the
nine positive mitre detents, simply lock
the turntable into desired angle position
by turning the mitre lock handle (10) in
the clockwise direction.
8.3 Precision adjustment of the
blade for crosscut 90°
(Fig. 1/2/6/7)
• No stop angle included.
• Move the head (4) in position, so that
the blade (6) rests directly above the
turntable (15). Now, use locking screw
(25) to lock the drag guide (26).
• Lower the machine head (4) and secure
using the fastening bolt (30).
• Loosen the bevel locking screw (27).
• Position the angle stop (a) between the
saw blade (6) and the turntable (15).
• Release the locking nut (c) and adjust
the adjusting screw (32) until the angle
between the saw blade (6) and turntable
(15) is 90°.
• Re-tighten the locking nut (c).
• Subsequently check the position of the
angle indicator. If necessary loosen the
pointer (24) using a Philips screwdriver,
set to position 0° on the angle scale (23)
and re-tighten the retaining screw.
8.4 Precision adjustment of stop
rail for crosscut 90°
(Fig. 1/8/9)
- Bring the power tool into the working
position.
- Turn the turntable (15) to the 0° on the
mitre angle scale (14). The metre detent
lever （11） must be felt to engage in
the detent.
GB / IE / NI 11