Installation - ROSIERES RHV 994 serie Montage- Und Gebrauchsanweisung

Instruction on mounting and use
Consult the designs in the front pages referenced in the
text by alphabet letters. Closely follow the instructions
set out in this manual. All responsibility,
eventual inconveniences, damages or fires caused by not
complying with the instructions in this manual,
declined.
Use
The hood is designed to be utilized either for suction
version at external evacuation or filtering version at
internal recirculation.
Fig. 6
Ducting version
The hood is equipped with a top air outlet B for discharge
of fumes to the outside (exhaust pipe and pipe fixing
clamps not provided).
Filter version
Should it not be possible to discharge cooking fumes and
vapour to the outside, the hood can be used in the filter
version, fitting an activated carbon filter and the deflector
F on the support (bracket) G, fumes and vapours are
recycled through the top grille H by means of an exhaust
pipe connected to the top air outlet B and the connection
ring mounted on the deflector F (exhaust pipe and pipe
fixing clamps not provided).
The models with no suction motor only operate in ducting
mode, and must be connected to an external suction
device (not supplied).

Installation

The minimum distance between the supporting surface
for the cooking vessels on the hob and the lowest part of
the range hood must be not less than 50cm from electric
cookers and 65cm from gas or mixed cookers.If the
instructions for installation for the gas hob specify a
greater distance, this must be adhered to.
Electrical connection
Th
e electrical tension must correspond to the tension
noted on the label placed inside the cooker hood.
Connect the electrical plug, where provided, to the an
easily accessible outlet in conformity with local standards
in force. Where an electrical plug is not provided (for
direct connection to electrical network) place a standards
approved bipolar switch with an aperture distance of not
less than 3mm (accessible) from the contacts.
Attention: substituting the supply cable must be carried
out by the authorised technical assistance service.
Mounting
Expansion wall plugs are provided to secure the hood to
most types of walls/ceilings. However, a qualified
technician must verify suitability of the materials in
accordance with the type of wall/ceiling. The wall/ceiling
must be strong enough to take the weight of the hood. Do
not tile, grout or silicone this appliance to the wall.
for any Surface mounting only.
Assembling the chimney flue support/bracket (3 parts):
is The three parts should be fixed with 4 screws, the support
extension is adjustable and should correspond to the
internal width of the telescopic chimney flue.
Assembling the deflector
composed of 3 parts is supplied – the deflector should
be only for the filter version):
The three parts should be fixed with 2 screws, the deflector
extension is adjustable and should correspond to the width
of the chimney flue support, to which it is then fixed.
=
X
Fig. 5-6
Disconnect the hood during electrical connection, by
turning the home mains switch off.
Remove the grease filter/s and the carbon filter frame.
1. Rest the suction unit on a flat surface and thread the
lower part of the hood onto it.
2. Make all the electrical connections between the two
parts.
3. Permanently fix the cooker hood to the suction group
with the 12 screws.
4. Using a pencil, draw a line on the wall, extending up to
the ceiling, to mark the centre. This will facilitate
installation.
5. Rest the drilling template against the wall: the vertical
centre line printed on the drilling template must
correspond to the centre line drawn on the wall, and
the bottom edge of the drilling template must
correspond to the bottom edge of the hood: bear in
mind that, when installation is complete, the underside
of the hood must be at least 50 cm above the cooker
top in the case of electric cookers, and at least 65 cm
above the cooker top in the case of gas or mixed
cookers.
8
(only when a deflector
G
F
=
X
F
H
X
=
=
G