Installation Instructions; Use And Maintenance - Beko CWB 6430 W Anleitung

- This device must be connected to the supply network
through either a plug fused 3A or hardwired to a 2 fase
spur protected by 3A fuse.
2. Warning!
In certain circumstances electrical appliances may
be a danger hazard.
A) Do not check the status of the filters while the
cooker hood is operating.
B) Do not touch bulbs or adjacent areas, during or
straight after prolonged use of the lighting instal-
lation.
C) Flambè cooking is prohibited underneath the
cooker hood.
D) Avoid free flame, as it is damaging for the filters
and a fire hazard.
E) Constantly check food frying to avoid that the
overheated oil may become a fire hazard.
F) Disconnect the electrical plug prior to any main-
tenance.
G) This appliance is not intended for use by young
children or infirm persons without supervision.
H) Young children should be supervised to ensure
they do not play with the appliance.
I) There shall be adequate ventilation of the room
when the rangehood is used at the same time as
appliances burning gas or other fuels.
L) There is a risk of fire if cleaning is not carried out
in accordance with the instructions.
This appliance conforms to the European Directive
EC/2002/96, Waste Electrical and Electronic Equipment
(WEEE). By making sure that this appliance is disposed
of in a suitable manner, the user is helping to prevent
potential damage to the environment or to public health.
The symbol on the product or on the accompanying
paperwork indicates that the appliance should not
be treated as domestic waste, but should be deliv-
ered to a suitable electric and electronic appliance
recycling collection point. Follow local guidelines when
disposing of waste. For more information on the treat-
ment, re-use and recycling of this product, please contact
your local authority, domestic waste collection service or
the shop where the appliance was purchased.

INSTALLATION INSTRUCTIONS

• Assembly and electrical connections must be
carried out by specialised personnel.
• Wear protective gloves before proceeding with
the installation.
• Electric Connection:
- The appliance has been manufactured as a class II,
therefore no earth cable is necessary. The plug must be
easily accessible after the installation of the appliance.
If the appliance is equipped with power cord without
plug, a suitably dimensioned omnipolar switch with 3
mm minimum opening between contacts must be fit-
ted between the appliance and the electricity supply in
compliance with the load and current regulations.
- The connection to the mains is carried out as follows:
BROWN = L line
BLUE = N neutral.
• If the hob is electric, gas, or induction, the minimum
distance between the same and the lower part of the hood
must be at least 65 cm. If a connection tube composed of
two parts is used, the upper part must be placed outside
the lower part. Do not connect the cooker hood exhaust
to the same conductor used to circulate hot air or for
evacuating fumes from other appliances generated by
other than an electrical source. Before proceeding with
the assembly operations, remove the anti-grease filter(s)
(Fig.5) so that the unit is easier to handle.
- In the case of assembly of the appliance in the suction
version prepare the hole for evacuation of the air.
• We recommend the use of an air exhaust tube which
has the same diameter as the air exhaust outlet hole. If a
pipe with a smaller diameter is used, the efficiency of the
product may be reduced and its operation may become
noisier.
• If your appliance has been designed for use in habita-
tions supplied with acentralised suction device perform
the following operations:
- The switch controls opening and closure of a valve using
a thermoelectical device. By placing the switch in the ON
position, after a minute, the valve opens rotating 90°
allowing suction of the stale air. By placing the switch in
the OFF position, the valve closes after 100 seconds.
• Fixing to the wall:
Drill the holes A respecting the distances indicated (Fig.2).
Fix the appliance to the wall and align it in horizontal
position to the wall units. When the appliance has been
adjusted, definitely fix the hood using the screws A
(Fig.4). For the various installations use screws and screw
anchors suited to the type of wall (e.g. reinforced concre-
te, plasterboard, etc.). If the screws and screw anchors are
provided with the product, check that they are suitable for
the type of wall on which the hood is to be fixed.
• Fixing the decorative telescopic flue:
Arrange the electrical power supply within the dimensions
of the decorative flue. If your appliance is to be installed in
the ducting version or in the version with external motor,
prepare the air exhaust opening. Adjust the width of the
support bracket of the upper flue (Fig.3). Then fix it to the
ceiling using the screws A (Fig.3) in such a way that it is in
line with your hood and respecting the distance from the
ceiling indicated in Fig.2. Connect the flange C to the air
exhaust hole using a connection pipe (Fig.4). Insert the
upper flue into the lower flue and rest above the frame.
Extract the upper flue up to the bracket and fix it with the
screws B (Fig.3). To transform the hood from a ducting
version into a filtering version, ask your dealer for the
charcoal filters and follow the installation instructions.
• Filtering version:
Install the hood and the two flues as described in the
paragraph for installation of the hood in ducting version.
To assemble the filtering flue refer to the instructions
contained in the kit. If the kit is not provided, order it from
your dealer as accessory. The filters must be applied to
the suction unit positioned inside the hood. They must
be centred by turning them 90 degrees until the stop
catch is tripped (Fig.6).

USE AND MAINTENANCE

• We recommend that the cooker hood is switched on
before any food is cooked. We also recommend that the
appliance is left running for 15 minutes after the food is
cooked, in order to thoroughly eliminate all contaminated
air. The effective performance of the cooker hood depends
on constant maintenance; the anti-grease filter and the
active carbon filter both require special attention.
• The anti-grease filter is responsible retaining the gre-
ase particles suspended in the air, therefore it is subject
to clogging with variable frequency according to the use
- 13 -