Dorr FX-3040 BC Bedienungsanleitung Seite 10

05 | MOUNTING
X-Frame
Unfold the X-frame (6) and insert the rods
into the fastening corners (5). With the
light stand adapter (7) the LED Flex Panel
can be mounted horizontally or vertically
onto a light stand (optional) and it is in-
clinable.
Velcro mounting straps
With the various Velcro straps (20), the
LED Flex Panel can be attached to the wall,
to the ceiling etc. or you can connect seve-
ral LED Flex Panels with each other.
06 | OPERATION
CAUTION
Before connecting or disconnecting cable connections, make sure that the control unit is
switched o (main switch (8) on position O = o ).
06.1 Power connection
Plug the connection cable of the LED Flex
Panel (2) into the connection cable of the
control unit (11). Pay attention to the pins
and holes. Screw the blue cap down.
To disconnect the cable connection, un-
screw the blue cap fi rst!
06.2 Operation with power supply
1. Plug the connection cable (17) of the
power supply into the power socket (9)
of the control unit, until the plug audibly
clicks into place. Pay attention to the
pins and holes. To disconnect the plug,
always press the release button!
2. Plug the power cable (19) into the power
cable socket (18) and connect the power
supply to a socket outlet.
3. Turn on the LED Flex Panel with the
main switch (8) at the control unit: Main
switch (8) position II = Operation with
power supply
Hint
With the suspension cord (12) or with the supplied Velcro strap with V-mount adapter (21)
you can attach the control unit e.g. to a light stand (optional) or fi x the power supply to
the control unit. Just slide the V-mount adapter (21) into the V-mount (13). Use the Velcro
straps to hold the control unit or to fi x the power supply. To remove the V-mount adapter,
press the release button (14).
06.3 Operation with V-mount battery
V-mount Li-Ion batteries are optionally available from DÖRR.
See capture 11 | OPTIONAL ACCESSORIES.
CAUTION
Before operating with V-mount battery, make sure that the control unit is switched o (main
switch (8) on position O = o ) and then disconnect the power supply from the control unit.
To disconnect the plug, always press the release button!
1. Slide the V-mount battery into the
V-mount (13) until the battery clicks into
place. Pay attention to the battery con-
tacts +/- (15).
2. Turn on the LED Flex Panel with the
main switch (8) at the control unit: Main
switch (8) position I = Operation with
V-mount battery
3. Before removing the V-mount battery,
turn the control unit off (main switch (8)
on position O). Press the release button
(14) and slide out the battery.
06.4 Setting of colour temperature and of illuminance
To adjust the colour temperature, press the buttons on the touch panel (10) as follows:
10 b) = colour temperature up
10 c) = colour temperature down
The indication 10 a) shows the selected colour temperature.
To adjust the illuminance, press the buttons on the touch panel (10) as follows:
10 e) = illuminance up
10 f) = illuminance down
The indication 10 d) shows the selected illuminance in %.
Examples for settings:
a) Setting for warmest light (3000 K)
Press the buttons on the touch panel (10) as follows:
10 c) = colour temperature down
10 e) = illuminance up
Touch display indicates:
b) Setting for daylight temperature (5600 K)
Press the buttons on the touch panel (10) as follows:
10 b) = colour temperature up
10 e) = illuminance up
Touch display indicates:
CAUTION
After use please turn o the LED fl ex panel (main switch 8 = position O).
10
(optional)
3000 K 100%
5600 K 100%