Ryobi RCS3840T Übersetzung Der Original-Anleitung Seite 11

hazards).
Thrown out pieces of the work piece (wood chips,
splinters).
Inhalation of saw dust and particles or emission from
the petrol engine.
Skin contact with petrol/oil.
RISK REDUCTION
It has been reported that vibrations from hand-held tools
may contribute to a condition called Raynaud's Syndrome
in certain individuals. Symptoms may include tingling,
upon exposure to cold. Hereditary factors, exposure to
cold and dampness, diet, smoking and work practices
are all thought to contribute to the development of these
symptoms. There are measures that can be taken by the
operator to possibly reduce the effects of vibration:
Keep your body warm in cold weather. When operating
the product wear gloves to keep the hands and wrists
warm. It is reported that cold weather is a major factor
contributing to Raynaud's Syndrome.
After each period of operation, exercise to increase
blood circulation.
Take frequent work breaks. Limit the amount of
exposure per day.
Protective gloves available from professional chainsaw
retailers are designed specifically for chainsaw use and
give protection and good grip. Gloves also reduce the
effect of handle vibration. These gloves should comply
with EN381-7 and must be CE marked.
If you experience any of the symptoms of this condition,
immediately discontinue use and see your doctor.
WARNING
Injuries may be caused, or aggravated, by prolonged
use of a tool. When using any tool for prolonged periods,
ensure you take regular breaks.
KNOW YOUR PRODUCT
See page 271.
PARTS
1. Chain
2. Guide bar
3. Front hand guard/Chain brake
4. Front handle
5. Air cleaner cover
6. Starter grip
7. Rear handle
8. Spiked bumper
9. Silencer cover
10. Fuel mix cap
11. Chain lubricant cap
12. Ignition switch
13. Trigger release
14. Throttle trigger
15. Primer bulb
16. Choke lever
17. Combination wrench
18. Sprocket cover
19. Chain catcher
20. Chain tensioner adjustment ring
21. Guide bar locking knob
22. Guide bar cover
SAFETY DEVICES
LOW KICK-BACK SAW CHAIN
A low-kick-back saw chain helps to reduce the possibility
of a kickback event.
The rakers (depth gauges) ahead of each cutter can
minimize the force of a kick-back reaction by preventing the
cutters from digging in too deeply. Only use replacement
guide bar and chain combinations recommended by the
manufacturer.
As saw chains are sharpened, they lose some the low
kickback qualities and extra caution is required. For your
safety, replace saw chains when cutting performance
decreases.
SPIKED BUMPER
The integral bumper spike may be used as a pivot when
making a cut. It helps to keep the body of the product
steady while cutting. When cutting, push the product
forward until the spikes dig into the edge of the wood, then
by moving the rear handle up or down in the direction of the
cutting line it can help ease the physical strain of cutting.
GUIDE BARS
Generally, guide bars with small radius tips have somewhat
lower potential for kick-back. Only use replacement
guide bar and chain combinations recommended by the
manufacturer. The use of unrecommended guide bars
increase the risk of loss of control during sawing. Regularly
check the chain tension. When cutting smaller branches
(less than the full length of the guide bar) the chain is more
likely to be thrown off if the tension is not correct.
CHAIN BRAKE
Chain brakes are designed to quickly stop the chain
rotation. When the chain brake lever/hand guard is pushed
towards the bar, the chain should stop immediately. A
Chain brake does not prevent kick-back. It only lowers the
risk of injury should the chain bar contact the operators
body during a kick-back event. The chain brake should be
tested before each use for correct operation in both the run
and brake positions.
CHAIN CATCHER
A chain catcher prevents the saw chain from being thrown
back towards the operator if the saw chain comes loose
or breaks.
SYMBOLS ON THE PRODUCT
Safety alert
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
English | 9