Inhaltsverzeichnis
Werbung
Power adjust button
Slide the button to adjust the suction power
3. Suction power adjustment: The suction power of the device can be adjusted individually ac-
cording to need with the power regulator. We recommend to set the suction power to mini-
mum for sensitive materials. Select medium power for mattresses, upholstered furniture and
carpets. For tiles, parquet flooring and other robust flooring the maximum suction power can
be used.
4. To retract the cable press the
button with one hand and with the other hand control the
cable to avoid damage by a resounding plug. -> If the cable does not fully retract: Pull the
cable back out a bit then press again the cable retract. These steps can be repeated until the
cable is completely rolled up.
REPLACING OR CLEANING THE DUST BAG
Note: Always turn off and unplug the vacuum cleaner and before changing the dust bag or
cleaning the motor filter. Never use the vacuum cleaner without the dust bag nor filter.
When the 'dust bag full' indicator lamp comes on, it indicates that the dust bag is full and needs
Replacing or cleaning the dust bag
to be cleaned or replaced.
While the dust bag full indicator lamp light on, it indicates out that the dust bag is full, and
1. Confirm the power supply is disconnected.
need to be cleaned or replaced.
2. Lift the front cover lock and open the front cover.
(1) Confirm the power supply is disconnected.
3. If a paper bag is used replace it with a new one.
(2) Lift the locking block of the front cover, and open the front cover.
4. Dust bag installation: Release the bag lock, slide the dust bag in the direction of the arrow
(3) If a paper bag is used, replace it with a new one.
until it reaches the bottom of the bag rack, then close the front cover.
(4) Dust bag installation: Pull out the bag lock ,Push the dust bag toward at the direction of
the arrow till it reach the bottom of the bag rack, then close the front cover.
Replacing or cleaning filters
(1) Confirm the power supply is disconnected.
(2) Open the front cover, remove the old air inlet filter to rinse and allow the filter to dry,
Caution: A system prevents the device to operate without a dust bag . When the dust bag is not
inserted correctly or missing, the lid will not close and the unit can not be put into operation (no
4
suction power).
MAINTENANCE
For cleaning an air inlet filter
1. Confirm the power supply is disconnected.
2. Open the front cover, remove the old air inlet filter, rinse and allow to dry. Then insert the air
inlet filter or a new filter and close the front cover.
then insert air inlet filter or a new filter and close the front cover.
then insert air inlet filter or a new filter and close the front cover.
(3) For replacing the air outlet HEPA, open the air outlet plate, take the dirty air outlet
HEPA out and replace it with a new one, close the air outlet plate.
(4) For washing the filters, please wash them in clean water, vibrate the filters to eliminate
Replacing or cleaning the air outlet filter (HEPA Filter)
excessive water, then put them at a shady or cool place for air-drying. Please assemble
them to the vacuum cleaner for using after they are completely dry, otherwise the motor
will be damaged.
1. To replace the air outlet HEPA, open the air outlet cover, remove the dirty air outlet HEPA and
(3) For replacing the air outlet HEPA, open the air outlet plate, take the dirty air outlet
HEPA out and replace it with a new one, close the air outlet plate.
replace it with a new one. Then close the air outlet cover.
then insert air inlet filter or a new filter and close the front cover.
(4) For washing the filters, please wash them in clean water, vibrate the filters to eliminate
excessive water, then put them at a shady or cool place for air-drying. Please assemble
2. To clean the filters, wash them in clean water, shake to eliminate excess water, then put them
them to the vacuum cleaner for using after they are completely dry, otherwise the motor
will be damaged.
in a shady or cool place to air-dry. Please wait until they are completely dry before refitting
them to the vacuum cleaner to avoid damage to the motor. Must be washed at least every six
months.
(3) For replacing the air outlet HEPA, open the air outlet plate, take the dirty air outlet
HEPA out and replace it with a new one, close the air outlet plate.
(4) For washing the filters, please wash them in clean water, vibrate the filters to eliminate
●
Must be washed at an interval of half year at least.
Must be washed at an interval of half year at least.
●
excessive water, then put them at a shady or cool place for air-drying. Please assemble
them to the vacuum cleaner for using after they are completely dry, otherwise the motor
will be damaged.
Must be washed at an interval of half year at least.
●
5
5
36 37
Machine Storage
Hang the brush on the back hook
Hang the floor brush on the base hook
5
Trouble Shooting
follow blow methods to deal with any abnormal problems happened，if cleaner still cannot
work，please contact the sales shop or authorized service center。
Description
Solutions
Cleaner
-
Check plug insert firmly or not，to unplug，insert socket again
don't
-
Check plug electrify or not。
running
-
Check switch is on or not。
Werbung
Inhaltsverzeichnis
