OBJ_BUCH-2577-001.book Page 15 Tuesday, October 6, 2015 11:33 AM
The integrated park rest 25 also allows for continued planing
at any given location on the workpiece after an interruption:
– With the park rest folded down, place the machine on the
location of the workpiece where the planing is to be contin-
ued.
– Switch on the machine.
– Apply the supporting pressure onto the front part of the
planer base plate and slowly push the machine forward
(). This tilts the park rest upward () so that the rear
part of the planer base plate faces on the workpiece again.
– Guide the machine over the surface to be planed () with
even feed.
Beveling Edges (see figure E)
The V-groove 8 in the front planer base plate allows quick and
easy beveling of workpiece edges. For this, place the planer
with the V-groove onto the edge of the workpiece and guide it
along the edge.
Groove to be used
none
medium
Planing with Parallel/Beveling Guide (see figures F–H)
Mount the parallel guide 17 or the beveling guide 21 on the
power tool (either at the front or back) with the fastening bolt
20. Depending on the application, mount the rebating depth
stop 24 on the power tool (either at the front or back) with the
fastening bolt 23.
Loosen the locking nut 19 and adjust the requested rebating
width on the scale 18. Tighten the locking nut 19 again.
Adjust the requested rebating depth accordingly with the re-
bating depth stop 24.
Carry out the planing procedure several times until the re-
quested rebating depth is reached. Guide the planer applying
sideward supporting pressure.
Beveling with the Beveling Guide
When beveling rebates and
surfaces, adjust the required
slope angle with the angle ad-
justment 22.
Maintenance and Service
Maintenance and Cleaning
Before any work on the machine itself, pull the mains
plug.
For safe and proper working, always keep the machine
and ventilation slots clean.
Ensure easy operation of the park rest 25 and clean it regular-
ly.
Bosch Power Tools
When the carbon brushes wear below acceptable service tol-
erances, the machine will automatically cut out. The machine
must be sent to customer service for maintenance (for ad-
dress, see the "After-sales Service and Application Service"
section).
If the replacement of the supply cord is necessary, this has to
be done by Bosch or an authorized Bosch service agent in or-
der to avoid a safety hazard.
After-sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Bosch's application service team will gladly answer questions
concerning our products and their accessories.
In all correspondence and spare parts orders, please always
Dimension a
include the 10-digit article number given on the nameplate of
(mm)
the product.
0 – 4
4 – 9
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham
Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: (01) 4666700
Fax: (01) 4666888
Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Phone: (01300) 307044
Fax: (01300) 307045
Inside New Zealand:
Phone: (0800) 543353
Fax: (0800) 428570
Outside AU and NZ:
Phone: +61 3 95415555
www.bosch.com.au
English | 15
1 609 92A 1AA | (6.10.15)