Bosch Runnʼn BGS4 serie Gebrauchsanleitung Seite 52

6*
Fig.
a) Place the accessories holder in the required positi-
on on the telescopic tube.
b) Use some pressure to insert the upholstery nozzle
with brush ring and the crevice nozzle into the ac-
cessories holder from above or below.
7*
Fig.
‡
Attach the accessories holder to the multi-purpose
nozzle and clip it onto the suction pipe/telescopic
tube.
8
Fig.
‡
Holding the power cord by the plug, pull it out to the
required length and insert the plug into the mains
socket.
9
Fig.
‡
To switch the vacuum cleaner on or off, press the
ON/OFF button.
Controlling the suction level
10
Fig.
Turn the control knob to infinitely adjust the suction
level to the level required.
„ Low power range
= For vacuuming delicate materials, e.g. delicate >
upholstery, curtains, etc.
„ Medium power range
= For daily vacuuming of lightly soiled floors. >
„ High power range
= For vacuuming durable floor coverings, hard floors >
and heavily soiled surfaces.
Vacuuming
!
Caution
Floor nozzles are subject to a certain amount of
wear, depending on the type of hard floors you have
(e.g. rough, rustic tiles). You must therefore check
the underside of the floor nozzle at regular intervals.
Worn undersides of floor nozzles may have sharp
edges that can damage sensitive hard floors, such as
parquet or linoleum. The manufacturer does not ac-
cept any responsibility for damage caused by worn
floor nozzles.
11
Fig.
Set the adjustable floor nozzle:
„ Rugs and carpets =>
„ Hard floors/parquet =>
If you are vacuuming up relatively large particles, make
sure that you vacuum them up successively and careful-
ly to ensure that the vacuum channel of the floor nozzle
does not become blocked.
If necessary, you should raise the nozzle in order to
better vacuum up the dirt particles.
Vacuuming with accessories
12*
Fig.
Attach the nozzles to the suction pipe or handle as re-
quired:
a) Crevice nozzle for vacuuming crevices and corners,
etc.
b) Upholstery nozzle for vacuuming upholstered furni-
ture, curtains, etc.
c) Upholstery nozzle with fixed brush ring for vacu-
uming window frames, cupboards, profiles, etc.
After use, reinsert the crevice nozzle and upholstery
nozzle into the accessories holder.
d) Professional crevice nozzle
Extra-long crevice nozzle for cleaning crevices, cor-
ners and narrow spaces, e.g. in a car.
e) Professional upholstery nozzle
For gently and thoroughly cleaning upholstered fur-
niture, curtains, etc.
For cleaning the professional upholstery nozzle, sim-
ply vacuum it using the handle.
f) Hard furnishings brush
For cleaning window frames, cabinets, mouldings,
etc.
g) Hard-floor nozzle
- with clip-in edge cleaning bristles:
For gentle but effective cleaning of hard floor
coverings (tiles, parquet, etc.)
- without edge cleaning bristles:
For cleaning dirt in gaps and cracks
‡
The edge cleaning bristles can be removed by
pushing the two catches in the direction of the
arrows.
Drill dust nozzle
13*
Fig.
‡
Fasten the drill dust nozzle onto the handle and po-
sition it on the wall so that the drill hole opening on
the nozzle is placed directly over where the hole is
to be drilled.
‡
Set the appliance to the lowest power level and then
switch it on.
‡
The drill dust nozzle is held in the required position
by suction. Depending on the condition of the wall to
be drilled, you may need to adjust to a higher power
setting to ensure that the drill dust nozzle remains
in place.
During drilling, the fine dust is automatically vacu-
umed up.
14
Fig.
You can use the parking aid on the back of the vacuum
cleaner if you want to stop vacuuming for a short time.
‡
After switching off the appliance, slide the hook on
the floor nozzle into the parking aid.
15
Fig.
When vacuuming stairs, the appliance must be positi-
oned at the bottom of the stairs. If it does not reach
far enough, the appliance can also be carried using the
carrying handle or the handle on the dust container.
* Dependent on model
45