Beninca HEADY 24 3B Handbuch Seite 16

The service light function is enabled or disabled on the 9/10 output (see Fig.3).
On: This output has the function of service light. At each operation, the output sup-
plies 24VAC for around 90 sec.
serl
The counting of the TLS time starts when the motor start.
Use an auxiliary relay to control the light.
Off: The output features the SCA function, open gate light: light off with closed gate,
flashing light with moving gate, light on with open gate. See wire diagram.
The operating mode of input 13/18 (PHOTO) is selected.
On: Input for the connection of the mechanical safety edge (Normally Closed (N..C.)
contact), activated in both opening and closing phases. The activation of the safety
edge causes the gate stop and its movement reversion for around 3 seconds. The
logics TST1 mush be OFF:
BAR
Off: Input for the connection of the photocell (N.C. contact), activated in both ope-
ning and closing phases. When the photocell switches on (open contact), the gate
movement will stop. When the photocell switches off (closed contact), the control unit
will always send an opening control signal to the system, even if the photocell was
activated during closure.
Enables or disables checking of photocells on PHOTO input, active both in closing
and in opening.
TST1
On: Check enabled. If the check has a negative result, no manoeuvre is commanded.
See Fig.4 - "PHOTO TEST".
Off: Checking of photocells disabled at each manoeuvre.
Enables or disables checking of photocells on PHOTC inputs, active only in closing.
On: Check enabled. If the check has a negative result, no manoeuvre is commanded.
TST2
See Fig.4 - "PHOTO TEST".
Off: Checking of photocells disabled at each manoeuvre.
Enables or disables motors check.
On: Check enabled. If the check has a negative result, no manoeuvre is command-
TSTm
ed.
Off: Check disabled.
(Enables or disables remote radiotransmitters learning, as indicated in the paragraph
"Remote transmitters learning".
rem
On: Remote learning enabled.
Off: Remote learning not enabled.
MENU
By selecting this function, the receiver goes in waiting (Push) for a transmitter code to assign to the step-step function.
Press the key of the transmitter to assign to this function.
PP
If the code is valid, it is memorised and the message OK is displayed
If the code is not valid, the message Err is displayed
By selecting this function, the receiver goes into waiting (Push) for a transmitter code to assign to the second radio chan-
nel.
2Ch
Press the key of the transmitter to assign to this function.
If the code is valid, it is memorised ad the OK message is displayed
If the code is not valid, the message Err is displayed.
By selecting this function, the receiver goes into waiting (Push) for a transmitter code to assign to the pedestrian opening
function.
ped
Press the key of the transmitter to assign to this function.
If the code is valid, it is memorised ad the OK message is displayed
If the code is not valid, the message Err is displayed.
By selecting this function, the receiver goes into waiting (Push) for a transmitter code to erase from the memory.
CLR
If the code is valid, it is erased and the message OK is displayed
If the code is not valid or not present in memory, the message Err is displayed
Completely erases memory of the receiver. Confirmation of the operation is requested.
RTR
By selecting this function the receiver goes into waiting (Push) for a new PGM pressure to confirm the operation.
At end of erasing the OK message is displayed
Displays the number of complete cycles (open+close) carried out by the automation.
When the <PG> button is pressed for the first time, it displays the first 4 figures, the second time it shows the last 4. Example <PG> 0012
>>> <PG> 3456: made 123.456 cycles.
16
RADIO (RADi)
CYCLES NUMBER (Nman)
FUNZIONE
(OFF)
(OFF)
(OFF)
(OFF)
(OFF)
(OFF)