Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
English
CE Compliance Information
Partron headset hereby declares that this PBH-200 is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC.
FCC Compliance Information
FCC ID : 2AD5K-PBH200
This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions:
This device may not cause harmful interference, and this device must accept any interference received,
including interference that may cause undesired operation.
Information to the user:
NOTE : This equipment has been tested and found to comply with limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However there is no guarantee that interference will not occur in a particular installation. If this equipment causes
harmful interference to radio or television reception can be determined by turning the equipment off and on.
The user is encouraged to try the correct interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
CAUTION TO USER : Changes or modifications not expressly approved by the party reasonable for compliance could void
the user's authority to operate the equipment.
Contents
PBH-200 User Manual
/ Package Contents /
Cable Clip
Earbud Covers
(Large, Small)
Charging Cable
Quick Manual
※ The components of above package are subject to change without notice to improve
the product performance or quality.
/ Description of Parts /
Micro USB
Volume Up
Volume Down
Play / Pause
Call
Mic 1
/ Installation of the Cable Clip /
Please hang the clip on the
headset band by opening it
a little bit.
※ The length of the cable from the headset's body to the user's ear can be easily adjusted
by pulling the clip higher or lower on the headset band.
/ Product Specifications and features /
Standby Time
Operating Time (Music)
Operating Time(Talk)
Charging Time
Battery
Working Distance
Supported profiles
Decoder
Bluetooth Version
Power Consumption
※ The above mentioned operating time may vary according to the surrounding enviroment and
the purpose of use.
/ How to use /
1. Power On / Off
Power On
- Press the call button for 1 second
- The red + blue LED light flashes for 0.5 second and a voice guide announces that
the power is turned on.
Power Off
- Press the call button for 3 seconds
- The red + blue LED light flashes for 0.5 second and a voice guide announces that
the power is turned off.
2. Battery Charging
LED indicator
- When the charger is connected, the Red LED is on.
- When charging is completed, the Blue LED is on.
※ When connected to the charger, the headset will be disconnected from the smartphone.
※ The power turns off if the USB charger gets disconnected.
Recommendations
- Using USB Hub may take extra charging time due to the low current.
For fast charging, please use a 5V 500mA ~ 5V 1A rated charger.
※ It takes approximately 2 hours to fully recharge a completely exhausted battery.
3. Battery Status Alarm & Alert
- Press Call and Volume + button at the same time for a second for audio guidance
about the current battery level.
"Battery Full" / "Battery Half" / "Battery not enough"
4. Low Battery Alarm & Alert
- The red LED light flashes 3 times with the voice guidance "Battery not enough"
when the battery power gets lower than for 1 hour of use.
5. Critical Battery
- The notice continues every 2 minutes when the battery power gets lower than
for 10 minutes of use and power is turned off with the voice guidance "Battery Empty"
at the critical battery state
6. Pairing
Before using the headset for the first time, you must pair it with a Bluetooth-enabled Device.
* Pairing: Connecting the Bluetooth-enabled smartphone to the Headset.
- Press the call button for 1 second to turn on the Headset.
- Once the power is on, the headset will automatically enter pairing mode.
(The red/blue LED light flashes)
The headset will automatically enter the waiting mode if it is not connected within 3 minutes.
(The power is automatically turned off after 50 minutes in the waiting mode)
- On the device you want to have paired, find the Bluetooth menu and search & select
"PBH-200" from the list of nearby Headsets.
- If connected without any problem, the headset will be paired accompanied by the audio
guide "Connected"
- The devices will be automatically paired after the first connection.
※ Manual Pairing on your smartphone: Turn the bluetooth function on.
- Press and hold the "call" button for 2 seconds to turn the device on.
It will automatically enter pairing mode with the voice guide "start pairing".
Select PBH-200 on the list of detected devices to connect
- If PIN code is required, please enter "0000"
Clearing the Paired Device
- Hold call button and Volume - button for 1 second after turning off the Bluetooth
of your mobile devices. Previously established connections will be deleted with
the voice guide "Clear paired list", and the device will enter pairing mode.
7. Calling
Voice Dial
- Briefly press Call button to activate Voice Dial.
※ To use Voice Dialing, your mobile phone must support Voice Dialing.
8. Call Answer / Call End / Call Reject
Call Answer / Call End
- Briefly press Call button to answer the incoming call.
- Briefly press Call button to end the call.
Call Reject
- Press and hold the Call button to reject the incoming call.
9. Call Transfer
- During the call, press Call button for 1 second to transfer the audio from headset to
mobile phone.
- Press Call button for 1 second again to transfer the audio from mobile phone
to headset.
10. Setting Waiting Mode while Calling
Setting Waiting mode
- During the call, briefly press Call button twice to put the caller on hold.
Press Call button twice again to return to the caller.
※ To use Call waiting mode, the mobile phone must support 'Call waiting' service.
Incoming second call while calling
- Briefly press Call button to end the original call and answer the second call.
- Briefly press Call button twice to answer the second call without hanging up the
original call (Original call will be on call waiting mode)
Ending a Call
- Briefly press Call button.
Package Contents
Description of Parts
Installation of Cable Clip
Product Specifications and Features
How to use
Power on/off
Battery Charging
Pairing
Calling
Transferring a Call
Volume Control
Music Play
Change language settings
Multi-Connection
Using Application
Button Functions & Status Information
Precautions
Product Warranty and Service
Limited Warranty
Product Warranty Certificate
Place it in a suitable position and
fix the earphone cable properly.
500 hours
14 hours
14 hours
2 hours
Lithium Polymer Battery 3.7V (195mAh)
10m
HFP / HSP / A2DP / AVRCP
SBC, APT-X
Version 4.1
0.5W
14
15
16
17
PBH-200
Mic 2
LED
Werbung
Inhaltsverzeichnis
