Fagor 6H-197A X Bedienungsanleitung Seite 23

3.3 Self-cleaning rough-walled models. On
these models, the rear plate and side panels
are covered with a self-cleaning enamel
that removes the grease while the oven is
functioning. The side panels are reversible,
doubling the lifetime of the coating.
If the panels are not performing the self-
cleaning process suffi ciently, they will need
regenerating. To do this, remove all the
accessories and utensils from the inside of
the oven. Thoroughly clean the oven surfaces
that are not self-cleaning. Select the
function.
Set the temperature to 250ºC and set the
time between 30 and 60 minutes, depending
on how dirty the oven is.
When the cleaning programme ends and
the oven has cooled down, wipe the self-
cleaning elements with a damp sponge. They
will then be totally functional again.
Pyrolytic ovens
3.4 Pyrolysis cleaning.
• The cleaning process consists of the dirt
being burnt at high temperatures.
• The smoke and smells are eliminated by a
catalyser.
• There is no need to wait until the oven has
accumulated a large amount of grease to
perform the cleaning process.
• After pyrolysis, when the oven has cooled
down, wipe it with a damp cloth to remove
the white ash residue.
• Before starting the pyrolysis process,
take all the accessories out of the oven,
including the cooking accessories and the
telescopic runners.
• If any substances are stuck to the inside of
the oven due to spill-overs, remove them
before carrying out the pyrolysis process
as they could catch fi re or give off large
amounts of smoke.
• During the pyrolysis process the surfaces
become hotter than during normal use.
Keep children away from the oven.
Depending on how dirty the oven is, you can
choose between two types of pyrolysis.
Pyrolysis : This type of pyrolysis should
only be used when the oven is very dirty. The
cleaning process takes 2 hours. To activate
it, turn the function selector dial
(3.4.1).
Note: Pyrolysis cleaning is possible with this
option, with the enamelled tray accessory.
Place it at level 2. First remove the excess
grease accumulated.
ECO pyrolysis : The cleaning process
takes 1 hour 30 minutes. To activate it, turn
the function selector
Note: The time and temperature parameters
are set parameters and cannot be altered.
When the process begins, the oven reaches
very high temperatures, the door safety lock
is activated and the pilot light beside the
symbol comes on (3.4.3). When the oven has
cooled down, the pilot light switches off and
the door can be opened.
3.5 Delayed pyrolysis. You can programme the
pyrolysis end time. Turn the function selector
dial and select
(3.5.2) or (3.5.3) until
fl ash. Adjust the pyrolysis end time by turning
the time selector dial
3.6 Cleaning the inside walls. Take out the side
runners and clean off any grease or ash that
has been left after the cleaning processes.
Depending on the models, the side runners
are fi xed in two ways, either without a
support (3.6.1, 3.6.2) or with a support
(3.6.4, 3.6.5). When you have removed them,
use a damp cloth to clean the side walls
(3.6.3, 3.6.6). When you have cleaned the
oven walls, replace the runners. If your oven
has a fold-down grill, pull upwards and press
to fold it down (3.6.7) and clean the top wall
with a damp cloth (3.6.8).
3.7 Cleaning the glass.
Cleaning the outside of the glass: Use a
soft cloth soaked in a glass cleaning product.
Cleaning the inside of the glass: If the
inside of the glass is dirty, you can remove it
for cleaning.
When the oven has cooled down, open
the door as far as it will go (3.7.1) and fi x
it in place with the red stops supplied in
the accessory bag (3.7.2). Insert the two
e n g l i s h
to
to (3.4.2).
or (3.5.1). Press
begins to
(3.5.4, 3.5.5).
21