Nice Neoplus ML Anweisungen Und Hinweise Für Die Installation Und Die Bedienung Seite 7

If a transmitter has not yet been memorized, the first can be memorized in Mode II as indicated in table A7.
Table "A7" Memorizing the first transmitter in mode II
1. Connect the motor to the mains power supply, 2 beeps are immediately heard
2. Within 5 seconds push and hold the transmitter button to be memorized
3. Release the button after the 3 beeps
4. Within 5 seconds start to push the same transmitter button the same number of times equal to the required
command: 1 = "Step-by-Step" 2 = "Up" 3 = "Down" 4 = "Stop"
5. After about 3 seconds the same number of beeps as the selected command are heard
6. Within 2 seconds push the same transmitter button
7. Release the button on the first of the 3 beeps which confirm the memorization.
If at point 5 the same number of beeps equal to the selected command are not heard, simply do not push any more buttons and wait a few seconds for the programming
to finish without memorizing.
After the transmitter has been memorized for the "Step-by-Step" or "Stop" commands, these commands are immediately available for use, while the movement direc-
tion must be programmed in order to use the "Up" ▲ and "Down" ▼, commands. Until the direction has been programmed, each ▲ and ▼, command from the trans-
mitter is signalled with a beep and two brief movements of the motor. Being that the movement direction cannot be programmed with the transmitter memorized in Mode
II, this operation must be performed with a transmitter memorized in Mode I or with the specific TTP or TTI programmers.
When one or more transmitters have already been memorized, others can be memorized in Mode II as indicated in table A8.
Table "A8" Memorization of additional transmitters in Mode II
1. Push and hold the button to be memorized of the new transmitter (approx. 5 seconds) until a beep is heard;
then release the button
2. Within 5 seconds push and hold the button of an old and already memorized transmitter (approx. 5 seconds)
until 2 beeps are heard; then release the button
3. Within 5 seconds start to push the same button of the old transmitter the same number of times equal to the
required command: 1 = "Step-by-Step" 2 = "Up" 3 = "Down" 4 = "Stop"
4. After about 3 seconds the same number of beeps as the selected command are heard.
5. Within 2 seconds push the same button of the new transmitter
6. Release the button on the first of the 3 beeps which confirm the memorization.
If at point 5 the same number of beeps equal to the selected command are not heard, simply do not push any more buttons and wait a few seconds for the programming
to finish without memorizing.
Note: if the memory is full (30 transmitters), 6 beeps are heard and the transmitter cannot be memorized.
A new transmitter can easily be memorized with the same characteristics as that of the old one by following the procedure in table A9.
The "new" transmitter will inherit the characteristics of the old one, i.e. if the old transmitter was memorized in Mode 1, the new one will also function in Mode 1, if the
old transmitter was memorized in Mode II then the button of the new transmitter will be associated to the same command as that of the old one.
Table "A9" Memorizing other transmitters
1. Press and hold down the pre-memorized button of the new transmitter (for approx.
3 seconds) then release the button
2. Press and hold down the pre-memorized button of the old transmitter (for approx.
3 seconds) then release the button
3. Press and hold down the pre-memorized button of the new transmitter (for approx.
3 seconds) then release the button
4. Press and hold down the pre-memorized button of the old transmitter (for approx.
3 seconds) then release the button
5. The memorization of the new transmitter is confirmed with 3 beeps
Note: If the memory is full (30 transmitters), 6 beeps will indicate that the transmitter cannot be memorized.
If the programming has to be cancelled and only one transmitter memorized in Mode II is available, the procedure in table A10 can be followed; (for cancellation with
a transmitter that has not been memorized or has been memorized in Mode I, see table A5).
The following can be deleted:
Table "A10" Cancellation of the memory with transmitter memorized in Mode II
1. Push and release a button memorized in Mode II (it doesn't matter if the motor starts to move, the motor
should stop at point 2)
2. Push and hold the same transmitter button (approx. 5 seconds) until a beep is heard and then release the button
3. Keep the same transmitter button pushed until 3 beeps are heard and
release the button during the third beep.
4. Keep the same transmitter button pushed until 3 beeps are heard and
release the button during the third beep.
➨
5. Keep the same transmitter button pushed until 3 beeps are heard and
release the button during the third beep.
6. To cancel everything:
Within 2 seconds, push the same transmitter button and
release the button on the first of the 5 beeps that confirm the cancellation.
• only the transmitter transmitters, finishing at point N. 5
• all data (transmitters, wind level), completing the procedure up to point 6.
Example
1-4
1-4
Example
New 5s
5s
Old
Old 1-4
1-4
New
Example
New >3s
Old >3s
New >3s
Old >3s
Example
5s
7
GB