Troubleshooting; Maintenance; Protecting The Environment - Black + Decker BESTA525 Bedienungsanleitung

Rewinding spool from bulk line (Fig. Q, R, S)
Replacement spools of cutting line are available from your
BLACK+DECKER dealer. Packs containing 3
spools of cutting line are also available.
Unplug the tool.

Remove the empty spool from the trimmer as described

in "REPLACING THE SPOOL".
Remove any remaining cutting line from the spool.

Make a fold at the end of the cutting line at about 19mm

(21). Feed the cutting line into one of the line anchoring
slots (22) as shown in Fig. Q.
Note: Take care not to allow the the line on the spool to
unravel. Hold it firmly with one hand at all times.
Insert the 19mm end of the bulk line into the hole (23) in

the spool adjacent to the slot as shown in Fig. R. Make
sure the line is pulled tight against the spool as shown in
Fig. S.
Wind the cutting line onto the spool in the direction of the

arrow on the spool. Make sure to wind the line on neatly
and in layers. Do not crisscross (Fig. S).
When the wound cutting line reaches the recesses (24),

cut the line. (Fig. R).
Fit the spool onto the trimmer as described in

"REPLACING THE SPOOL.
Warning! Before you begin trimming, only use the appropriate
type of cutting line.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
Safely dispose of the old plug.

Connect the brown lead to the live terminal in the new

plug.
Connect the blue lead to the neutral terminal.

Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 13 A.

Troubleshooting

If your tool seems not to operate properly, follow the
instructions below. If this does not solve the problem, please
contact your local BLACK+DECKER repair agent.
Warning! Before proceeding, unplug the tool.
Machine runs slowly
Check that the spool housing can rotate freely. Carefully

clean it if necessary.
Check that the cutting line does not protrude more than

approximately 136mm from the spool. If it does, cut it off
so that it just reaches the line trimming blade.
Automatic line feed does not work
Remove the spool cap.

(Original instructions)
Pull the cutting line until it protrudes approximately 136mm

from the spool. If insufficient cutting line is left on the
spool, install a new spool of cutting line.
Ensure that the line is not crisscrossed on the spool as

detailed in Fig. S. If it is, unwind the cutting line, then wind
it back on the spool neatly so that the lines do not cross.
Ensure the beginning of the cutting line is pulled tight

against the spool as shown in Fig. S.
Align the tabs on the spool cap with the cut outs in the

housing.
Push the spool cap onto the housing until it snaps

securely into place.
If the cutting line protrudes beyond the trimming blade,

cut it off so that it just reaches the blade. If the automatic
line feed still does not work or the spool is jammed, try the
following suggestions:
Carefully clean the spool and housing.

Remove the spool and check if the lever in the spool

housing can move freely.
Remove the spool and unwind the cutting line,

then wind it on neatly again. Replace the spool into
the housing.

Maintenance

Your BLACK+DECKER corded/cordless machine/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation
depends upon proper tool/machine care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
Switch off and unplug the machine/tool.

Or switch off and remove the battery from the machine/

tool if the machine/tool has a separate battery pack.
Or run the battery down completely if it is integral and then

switch off.
Unplug the charger before cleaning it. Your charger does

not require any maintenance apart from regular cleaning.
Regularly clean the ventilation slots in your tool/machine

and charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do

not use any abrasive or solvent-based cleaner.
Regularly clean the cutting line and spool using a soft

brush or dry cloth.
Regularly use a blunt scraper to remove grass and dirt

from the underneath of the guard.

Protecting the environment

Z
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste
ENGLISH
11