Inhaltsverzeichnis
Werbung
SURROUND SOUND
Dolby Pro Logic
Dolby Pro Logic is a coding system that enables a
VCR
set to decode 4 sound channels out of a normal
A
stereo signal: the centre channel for picture related
PROLOGIC
PRO-LOGIC
sounds, both front left and right channels for stereo
sounds and one surround channel to bring room
A
VCR
and depth to the scene.
PRO-LOGIC
Dolby Pro Logic manufactured under license from
Dolby Laboratories Licensing Corporation.
DOLBY, the double-D symbol
and 'PRO
LOGIC' are trademarks of Dolby Laboratories
Licensing Corporation.
A full Pro Logic system needs 5 speakers that should
be connected and positioned as shown below.
VCR
PRO-LOGIC
CENTER
TV
LEFT
RIGHT
STEREO
VCR
SURROUND
SURROUND
LEFT
RIGHT
SYSTEM REMOTE CONTROL
Changing the batteries
If the range of your infrared remote control seems to
1
2
decrease, or if certain individual functions can no
longer be carried out, you should replace the
6
7
batteries.
Two micro 1.5 Volt LR03 size AAA are required. To
P
change the batteries, open the compartment on the
back of the remote control. Ensure that the batteries
P
are inserted properly (note the markings in the
compartment).
P
In the interest of the environment: Remember that
batteries must always be disposed of properly.
REAR
SURROUND
General controls
–
y HIFI – To switch the HIFI system to STAND BY.
$
STATION
VOLUME +/– – Controlling the volume of the
amplifier (provided the HIFI - TV/VCR switch is in
position HIFI).
RECORD
– For muting the speakers (provided the HIFI -
TV/VCR switch is in position HIFI).
SURROUND INSTALL This button is used to switch
between SURROUND (DOLBY PRO LOGIC) and
STEREO mode and to enter the installation mode for
surround settings.
REAR – to call up rear level adjustment mode or to
VOLUME
manipulate the different surround settings
CENTRE + to call up centre level adjustment mode
or to manipulate the different surround settings
Selecting the surround mode
• Press briefly the SURROUND INSTALL button to
switch the surround mode on.
The display shows briefly PROLOGIC and then
the selected source again.
– The indication
-
remains on the display.
PRO
LOGIC
PRO LOGIC
Choose this setting for playback of music and
movies (especially Laser Discs, videocassettes and
TV broadcasts with DOLBY SURROUND sound).
Not only does Dolby Pro Logic surround you with
sound, it also gives you a clear perception of the
position and direction of the sound.
In this mode you use 5 speakers: front left and right,
a centre speaker and two rear speakers. .
• Press again briefly the SURROUND INSTALL
button to switch the surround mode off.
The display shows briefly STEREO and then the
selected source again.
-
does not light
PRO
LOGIC
up anymore.
STEREO
In this case the centre and rear speakers are
switched off for normal stereo operation.
Note: the surround mode Dolby Pro Logic will not
work properly if the signal passes through a graphic
equalizer. Please refer to your equalizer user
manual for guidance on switching off (or defeating)
the equalizer.
To control the functions of the sources TUNER, CD
or TAPE, make sure that the HIFI - TV/VCR switch
3
4
5
is in the position HIFI
TUNER
8
9
0
AV
TUNER/pty – For selecting the radio and for
selecting the programme type (PTY) mode.
P
10-button keypad for directly selecting stations
$ # STATION – For selecting stations, to select
P
programme types in the PTY mode or to select
characters in the station name input mode.
P
S T – To start tuning up/down or to move
CENTRE
the cursor in the station name input mode.
TXT/ – To change the information shown in the
Install
+
display or to enter the station name input mode.
#
CD
CD/disc – For selecting the CD player and to enter
the disc selection mode when using a CD-changer.
10-button keypad for directly selecting tracks
; – To switch the CD player to PAUSE.
9 – To switch the CD player to STOP.
HIFI
TV/VCR
B – To start and restart playback of the CD player.
S T – To select next or previous tracks on a
CD, to search forward and backward or to select a
disc when using a CD-changer.
TXT/ – To change the information shown in the
display.
TAPE
TAPE A B– For selecting the cassette deck and for
selecting the tape travel direction.
B – To start playback.
9 – To switch the cassette deck to STOP.
; – To switch the cassette deck to PAUSE.
S T – For fast winding of the tape in forward
or reverse direction or to search for next or previous
tracks during playback.
RECORD 0 – To start recording
ADAPTING THE SURROUND MODE VALUES
Adapting the Surround mode values
> 1.5 SEC
The surround mode has programmed values for
I N ST A LL
PRO-LOGIC
centre-mode, centre and rear levels and for rear
SURROUND
INSTALL
N O RM A L
channel time delay which are suitable for most
PRO-LOGIC
common applications.
You can , however, change these settings to your
particular taste or speaker installation.
– REAR
CENTRE +
To install your Surround system proceed as
D E LA Y 20
PRO-LOGIC
follows:
SURROUND
• Press the SURROUND INSTALL key longer than
INSTALL
1,5 seconds.
– REAR
– The display shows first 'INSTALL' and
changes then to e.g.'NORMAL'.
• Use the CENTRE + and – REAR buttons to
TE ST
PRO-LOGIC
select the centre channel mode: NORMAL,
SURROUND
WIDE or PHANTOM.
TE S T F L
INSTALL
PRO-LOGIC
– Select NORMAL if you are using a normal
T E ST _ C 0
PRO-LOGIC
centre speaker.
– Select WIDE if you have connected a HiFi
– REAR
CENTRE +
T E ST F R
PRO-LOGIC
centre speaker
– Select PHANTOM if you have not connected a
PRO-LOGIC
centre speaker, but still wish to simulate the
– REAR
CENTRE +
sound coming from the centre.
• Press the SURROUND INSTALL button again.
– The display shows e.g. DELAY 20.
RE A R
PRO-LOGIC
• Use the CENTRE + and – REAR buttons to
– REAR
adjust the delay time of the rear channel
(between 15 and 30 ms). Increasing the rear
delay time expands the perceived listening
– REAR
area, and vice versa.
C EN T RE 0
PRO-LOGIC
CENTRE +
– REAR
SYSTEM REMOTE CONTROL
TV
TV – For selecting the TV set (when connected to the
1
2
TV input).
y TV – To switch the TV to STAND BY.
6
7
?
3 @ @ @ @ @ @ 5 ? J @ @ @ L f ?
@ @ @ @ @ @ @ @ e @ @ @ ? f ?
– For selecting next or previous TV stations.
N @ @ @ @ @ @ H ? 7 @ @ @ 1 f ?
? N @ @ @ ( Y ? 7 @ @ @ @ @ 1 ? e ?
? 3 @ @ @ @ 5 ? J @ @ @ @ @ L ? e ?
3 @ @ H ? J @ @ @ @ @ @ @ L e ?
V 4 @ ? ? @ @ @ @ @ @ @ @ @ e ?
?
P
To control the following functions of the TV, make
sure that the HIFI - TV/VCR switch is in the
position TV/VCR
P
10-button keypad for directly selecting stations .
TXT/ – For selecting teletext.
P
– For muting the speakers.
REAR
SURROUND
VOLUME +/– – For controlling the volume of the
TV.
–
SAT
$
STATION
SAT – For selecting the satellite receiver (when
connected to the TV input).
y SAT – To switch the satelite receiver to STAND
RECORD
BY.
@ @ @ @ @ @ @ @ e @ @ @ ? f ?
?
– For selecting next or previous satellite
3 @ @ @ @ @ @ 5 ? J @ @ @ L f ?
? 3 @ @ @ @ 5 ? J @ @ @ @ @ L ? e ?
N @ @ @ @ @ @ H ? 7 @ @ @ 1 f ?
? N @ @ @ ( Y ? 7 @ @ @ @ @ 1 ? e ?
3 @ @ H ? J @ @ @ @ @ @ @ L e ?
V 4 @ ? ? @ @ @ @ @ @ @ @ @ e ?
?
programmes.
VCR
VCR – For selecting the video recorder (when
connected to the VCR input).
VOLUME
@ @ @ @ @ @ @ @ e @ @ @ ? f ?
?
– For selecting next or previous VCR stations.
3 @ @ @ @ @ @ 5 ? J @ @ @ L f ?
? 3 @ @ @ @ 5 ? J @ @ @ @ @ L ? e ?
N @ @ @ @ @ @ H ? 7 @ @ @ 1 f ?
? N @ @ @ ( Y ? 7 @ @ @ @ @ 1 ? e ?
V 4 @ ? ? @ @ @ @ @ @ @ @ @ e ?
3 @ @ H ? J @ @ @ @ @ @ @ L e ?
?
To control the following functions of the video
recorder, make sure that the HIFI - TV/VCR switch
is in the position TV/VCR
B – To start playback of the video recorder.
RECORD 0 – To start recording.
9 – To switch the video recorder to STOP.
; – To switch the video recorder to PAUSE.
Q R – Fast winding of the tape in forward or
reverse direction.
• Press the SURROUND INSTALL button again.
– You will now hear a test tone from the left,
centre, right and rear speakers in turn, in a
repeating cycle.
– The display shows e.g. TEST FL
TEST_C 0
TEST FR
TEST_R 0
TEST FL
• The values of the centre and rear level can be
adjusted if you press CENTRE + or – REAR
during the 2 seconds that you hear the test
tone of the centre TEST_C 0 and the rear
speaker TEST_R 0.
CENTRE +
• When you are satisfied with the levels, press
the SURROUND INSTALL button again to turn
off the test tone and leave the installation mode.
Note: When you have selected PHANTOM for the
centre channel mode, the test tone sequence will be
as follows: TEST FL
TEST FR
TEST_R 0
TEST FL
Direct adjustment of rear and centre level
T ES T _R 0
During e.g. a film, it is possible that the special
effects on the rear speakers become too loud or
too quiet compared to the level of the dialogue,
making it necessary to perform small adjustments.
Your unit is, for this purpose, provided with two
keys for direct adjustment:
0
Adjusting the rear level
• Press the – REAR button.
The display shows e.g. REAR 0.
CENTRE +
• If you press within 2 seconds the CENTRE + or
– REAR buttons you can adjust the rear level
(related to the front level).
Adjusting the centre level
• Press the CENTRE + button.
The display shows e.g. CENTRE 0.
• If you press within 2 seconds the CENTRE + or
CENTRE +
– REAR buttons you can adjust the centre level
(related to the front level).
Operation of other brands
This remote control can be used to operate also
3
4
5
other brands of TV's, Satellite receivers and Video
8
9
0
recorders. The codes for these other brands have
AV
already been put in the memory.
For TV sets you can select 5 different presets, for
P
Satellite receivers 3 and for Video recorders 10
different presets.
P
How to select the right presets?
for TV sets
P
• Keep the TV button pressed and press one of the
CENTRE
number 1...5 of the numeric keys for approx. 6
seconds.
Install
+
TV 1
– On the display of your amplifier appears e.g.
.
• To control if you have selected the right code,
#
?
@ @ @ @ @ @ @ @ e @ @ @ ? f ?
press e.g. one of the
N @ @ @ @ @ @ H ? 7 @ @ @ 1 f ?
3 @ @ @ @ @ @ 5 ? J @ @ @ L f ?
buttons.
? 3 @ @ @ @ 5 ? J @ @ @ @ @ L ? e ?
? N @ @ @ ( Y ? 7 @ @ @ @ @ 1 ? e ?
3 @ @ H ? J @ @ @ @ @ @ @ L e ?
V 4 @ ? ? @ @ @ @ @ @ @ @ @ e ?
?
– If your TV reacts to this command you have
selected the right preset.
– If your TV does not react, try to select another preset.
for Satellite receivers
• Keep the SAT button pressed and press number
HIFI
TV/VCR
1, 2 or 3 of the numeric keys for approx. 6
seconds.
SAT 1
– On the display of your amplifier appears e.g.
.
• To control if you have selected the right code,
press e.g. one of the
@ @ @ @ @ @ @ @ e @ @ @ ? f ?
?
buttons.
3 @ @ @ @ @ @ 5 ? J @ @ @ L f ?
? 3 @ @ @ @ 5 ? J @ @ @ @ @ L ? e ?
N @ @ @ @ @ @ H ? 7 @ @ @ 1 f ?
? N @ @ @ ( Y ? 7 @ @ @ @ @ 1 ? e ?
3 @ @ H ? J @ @ @ @ @ @ @ L e ?
V 4 @ ? ? @ @ @ @ @ @ @ @ @ e ?
?
– If your Satellite receiver reacts to this command
you have selected the right preset.
– If your Satellite receiver does not react, try to
select another preset.
for Video recorders
• Keep the VCR button pressed and press one of
the numeric keys (1...0) for approx. 6 seconds.
VCR 1
– On the display of your amplifier appears e.g.
.
• To control if you have selected the right code,
press e.g. one of the
@ @ @ @ @ @ @ @ e @ @ @ ? f ?
?
buttons.
3 @ @ @ @ @ @ 5 ? J @ @ @ L f ?
? 3 @ @ @ @ 5 ? J @ @ @ @ @ L ? e ?
N @ @ @ @ @ @ H ? 7 @ @ @ 1 f ?
? N @ @ @ ( Y ? 7 @ @ @ @ @ 1 ? e ?
3 @ @ H ? J @ @ @ @ @ @ @ L e ?
V 4 @ ? ? @ @ @ @ @ @ @ @ @ e ?
?
– If your VCR reacts to this command you have
selected the right preset.
– If your VCR does not react, try to select another preset.
Werbung
Inhaltsverzeichnis
