Reloop RMP1700RX Bedienungsanleitung Seite 17

3.6 Pitch Fine Adjustment
Via the Pitch Range Button -19-/38.2 it is possible to select a pitch range of +/-4%, +/-8%, +/-16% or +/-100% (a pitch range of +/-100% is only
available for audio CDs). Via the Pitch Fader -23/38.3- you can now steplessly adjust the CD's or USB device's pitch in the selected range. The
difference in pitch compared to the original pitch is shown on the display -F-. By using the Pitch Bend Buttons -22- it is possible to change the
track's pitch by the percentage within the selected pitch range. When releasing the button the player returns to the pitch that has been previously
adjusted via the Pitch Fader -23-. By pressing the Pitch Reset Button, the pitch value will be set back to 0%.
NOTE!
By turning the Jog Wheel -7- in playback mode the pitch can be increased by +100% (clockwise) or decreased by -100% (counterclockwise) as well.
> For further information please see chapter "Jog Wheel Mode".
3.7 Cueing
When pressing the Cue Button/Loop In Button -13/40- during playback mode the player will return to the track's beginning and will enter pause
mode if no cue point has been set. If a cue point has been set the player will return to the cue point and enter pause mode. You can set a cue point
by pressing the Play/Pause Button -14/41-, thus entering pause mode. Now via the Jog Wheel -7- it is possible to search for the desired cue point
by frame. Afterwards press the Cue Button -13/40- in order to save the cue point. By holding the Cue Button you will constantly return to playback
mode until you release the button; afterwards the player returns to the cue point and will be in pause mode. By pressing the Play/Pause Button
you will return to playback mode.
3.8 Looping
A loop is the permanent repetition of a sequence between a determined loop starting and ending point. Select a loop starting point by pressing the
Cue Button/Loop-In Button -13/40- once. The LED flashes. Select the loop ending point by pressing the Loop-Out Button -14/41- once. The Player
will switch to seamless-loop mode. The selected sequence will be repeated until the Loop-Out Button -14/41- will be pressed again; the player then
returns seamlessly to playback mode.
By means of the Reloop Button -14/42- you can activate the stored loop or jump to the loop respectively. In order to stop the seamless loop press
the Loop-Out Button -14/41.
By shortly pressing the Reloop Button -14/42- the last set loop will return to the loop in point and then played again. By pressing the Reloop Button
-14- for a longer period you will enter your loop's fine adjustment. You will start with the loop-out point that can be adjusted by frame by turning
the Jog Wheel -7-. In order to exit the fine adjustment at this point, press the Loop-Out Button -14/41-.
After having determined the loop-out point you can enter the loop's edit mode by pressing the Reloop Button -13-. The loop can in turn be adjusted
by frame via the Jog Wheel. In order to exit the fine adjustment at this point, press the Loop-Out Button -14/41-.
3.9 BPM Function
The media player disposes of an automatic BPM counter. Additionally it is possible to manually count the BPM value via the TAP/BPM Button -17-.
To do so the TAP/BPM Button -17- has to be pressed to the beat of the music. In order to return to the automatic BPM- counter mode the TAP/BPM
Button -17- has to be pressed and held for one second. Now you will enter the automatic counter again.
3.10 Keylock
When activating the keylock function via the button -21- the original track's key will be kept, independently from the adjusted pitch. Press the
button again in order to deactivate the keylock function.
3.11 End of Operation
Before turning the device off via the ON/OFF Button -1- make sure that no CD is inserted in the CD player. Also make sure that the CD Tray -2- is
closed. Should this not be the case after turning off the device, turn it on again and close the open CD tray via the Open/Close Button -4/31-.
3.12 Recording
It is possible to record any desired input source (CD/USB/RCA) to a USB storage device. In order to select a recording source or to carry out further
adjsutments, please refer to chapter 4, paragraphs 5-9.
Start to record by pressing the Rec Button -45- during playback. The recording process starts onto the previously selected storage device. In order to
stop your recording, press the Rec Button -45- once again. Your recording will now be written onto the storage device. By pressing the Mark Button
-44-, your recording will be turned seamlessly into a file. This way you can divide your recording into several segments.
By using the Rec Mode Button -24-, it is possible to switch the displayed information between playback mode and rec mode. If the Rec Mode LED
is lit, the display information is divided as follows:
1. Elapsed Time: Shows the elapsed time of a recording.
2. Remain Time: Shows the remaining time of a recording.
3. Total Remain: Shows the available space on your storage device. Please note that the length depends from the storage
capabilities of the recording media.
If the Clip LED -25- lights up, the recording volume is too high. Adjust this as described under 4.7.
17