DeWalt DWE314 Originalanweisungen Seite 26

EngLIsh

CAUTION: To avoid injury, ensure adaptor and accessory
are securely tightened.
Non-D WALT accessories can be attached using the
e
universal adaptor.
1. Place the washer on the tool.
11
2. Place accessory on to washer.
3. Tighten and secure adaptor nut
Attaching the Cut Guide (Fig. G–L)
The depth/cut guide allows you to precisely cut material at a
specified depth and more accurately track a marked cut line.
1. Attach the cut guide block
tabs 13 on the guide into the accessory side mount slots
on the main body of the tool.
2. Secure the block to the main body with the supplied screw
assembly 15 . Tighten with the supplied hex key
Depth Guide
This feature allows you to precisely cut material at a
specified depth.
1. Insert the guide arm as shown in figure H into the front
7
slot on the guide block 6 .
2. Adjust the length of the guide by pulling out or pushing
inward to achieve the desired cut depth as shown in figure I.
3. Secure the guide in place by turning the depth/cut
adjustment knob 14 clockwise. To release the guide turn
the depth/cut adjustment knob counterclockwise.
Cut Guide
This feature allows you to more accurately track a marked
cut line.
1. Insert the guide arm 7 as shown in figure J into the slots on
the left and right sides of the guide block
2. Adjust the length of the guide by pulling out or pushing
inward to achieve the desired length as shown in figure K.
3. Secure the guide in place by turning the depth/cut
adjustment knob 14 clockwise. To release the guide turn
the depth/cut adjustment knob counterclockwise.
nOtE: The guide arm can also be placed in the guard assembly
vertically in order to set the height off a cut. Refer to figure L.
Attaching the Dust Extraction Adaptor
(Fig. P)
The Dust Extraction Adaptor allows you to connect the tool to
an external dust extractor, either using the AirLock™ system
(DWV9000-XJ), or a standard 35 mm dust extractor fitment.
1. Attach the dust extraction adaptor
tabs in to the accessory side mount slots
13
2. Insert screw assembly 15
adaptor 17 and tighten with the supplied hex key
OPERATION
Instructions for Use (Fig. M, N)

WARNING: Always observe the safety instructions and
applicable regulations.
24
12 using a hex wrench.
6 by inserting the accessory
16 .
6 .
17 by inserting the
.
5
into the dust extraction
16 .

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. Be sure the
trigger switch is in the OFF position. An accidental start-up
can cause injury.

WARNING: Ensure switch is fully OFF before plugging in
the power cord.
1. Plug in power cord.
2. To turn the tool ON, hold it as shown in figure M and press
the variable speed trigger
nOtE: The further the trigger switch is depressed the faster
the tool will operate. If in doubt about the proper speed
5
for your operation, test the performance at low speed and
gradually increase until a comfortable speed is found.
3. To turn the tool OFF, release the variable speed trigger
Lock-on Button (Fig. N)
For more comfort in extended use applications, the
lock-on button can lock the trigger trigger
4
depressed position.
LED Worklight (Fig. O)
The LED worklight will activate when the trigger is depressed
2
Proper Hand Position (Fig. M)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires the tool to be held as shown in
Figure M.
Using the Dust Extraction Adaptor with the
Sanding Platen (Fig. Q)
1. Attach the dust extraction adaptor
the Dust Extraction Adaptor.
2. Attach the sanding platen
Removing Accessories.
3. Attach sanding sheet as described under Installing/
Removing Sanding Sheets.
Using the Dust Extraction Adaptor with
Plunge Cutting Accessory (Fig. R)
1. Attach the dust extraction adaptor. Refer to Attaching the
Dust Extraction Adaptor.
2. Push dust extraction arm
dust extraction adaptor
3. Attach plunge cutting bit as described under Installing/
Removing Accessories.
4. Adjust the dust extraction arm
1 .
in the
1
17 . Refer to Attaching
9 as described under Installing/
into the lower aperture of the
19
.
17
for best results.
19
.
1